The objective of the present study was to evaluate the cytotoxicity and degree of monomer conversion of resin-reinforced glass ionomer cements (RGIC) over different time periods. Four RGICs: Fuji Ortho LC (FOLC), Fuji Ortho Band (FOB), Orthoglass (OGL), and Multicure Glass Ionomer (MCI) were evaluated for cytotoxicity in fibroblastic L929 cells and for their degree of monomer conversion over different time periods. Three control groups were also analysed: positive control (C+), consisting of Tween 80 cell detergent; negative control (C-), consisting of phosphate-buffered saline; and cell control (CC), consisting of cells exposed to any material. To evaluate the cytotoxicity, the dye-uptake technique was used and the degree of conversion was evaluated using infrared spectroscopy. The data obtained were analysed by analysis of variance and the Tukey's test. The results showed cytotoxicity of the RGICs at 1 and 24 hours; the viability values of these materials were statistically different from the C- and CC groups (P < 0.05). After 48 hours, the FOLC group was statistically similar to the CC and C- groups but different from the others. At 1 hour, there was no difference in the degree of conversion between the FOLC and OGL groups (P > 0.05) or between the FOB and MCI (P < 0.05) groups. However, at 48 hours, the FOLC group had greater conversion values than the other groups (P < 0.05). There is a direct relationship between the degree of conversion and RGIC cytotoxicity. Following initial polymerization, cytotoxicity decreases and, consequently, the degree of conversion of the material increases.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1093/ejo/cjr009 | DOI Listing |
RSC Mechanochem
December 2024
Inorganic Chemistry and Catalysis, Institute for Sustainable and Circular Chemistry, Utrecht University Universiteitsweg 99 3584 CG Utrecht The Netherlands
Ball-milling of addition polymers such as polyolefins, polystyrene and polyacrylates can be used for depolymerization to obtain the respective monomers. However, absolute yields are typically low, especially from polyolefins which are notoriously difficult to depolymerize. To increase the viability of ball milling as a recycling technique, the effect of milling parameters on small hydrocarbon and monomer yields has to be understood.
View Article and Find Full Text PDFDent Mater
January 2025
KU Leuven, Department of Oral Health Sciences, BIOMAT & UZ Leuven, Dentistry, Kapucijnenvoer 7, 3000 Leuven, Belgium. Electronic address:
Objectives: To evaluate the effect of different zirconia compositions and manufacturing processes on the light irradiance (LI), to measure the degree of conversion (DC) of solely light-curing restorative composite underneath these zirconia grades and to evaluate the respective zirconia microstructures.
Methods: Six dental zirconia grades (GC HT, GC UHT [GC]; Katana HT, Katana UTML [Kuraray Noritake]; Lava Esthetic, Lava Plus [3 M Oral Care]) were cut and sintered per manufacturer instructions. One 3D-printed zirconia grade (XJet [XJET]) was prepared according to previous research.
Dent Mater
January 2025
Department of Engineering Mechanics, School of Civil Engineering, Wuhan University, Wuhan, Hubei 430072, China; Wuhan University Shenzhen Research Institute, Shenzhen 518108, China. Electronic address:
Objective: Photopolymerized resin composites are widely used as dental filling materials. However, the shrinkage stress generated during photopolymerization can lead to marginal microcracks and eventual restoration failure. Accurate assessment of the stress evolution in dental restorations, particularly in complex cavity geometries, is critical for improving the performance and longevity of the dental filling materials.
View Article and Find Full Text PDFJ Appl Microbiol
January 2025
Pilot Base of Food Microbial Resources Utilization of Hubei Province, College of Life Science and Technology, Wuhan Polytechnic University, Wuhan 430023, China.
Aims: Flavobacterium strains are widely distributed in various environments and generally exhibit specialized roles in the degradation of complex organic substrates. To obtain a deeper understanding of their enzyme profiles, patterns of action on natural carbohydrates degradation, and to mine gene resources for biomass conversion.
Methods And Results: We sequenced the whole genome of a novel carbohydrate-degrading Flavobacterium sp.
Langmuir
January 2025
Key Laboratory of Eco-Environment-Related Polymer Materials, Ministry of Education, Key Laboratory of Polymer Materials of Gansu Province, College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou, Gansu 730070, P. R. China.
Controllable transformation between the bolaamphiphilic molecule assemblies with different morphological nanostructures represents an exciting new direction for materials. However, there are still significant challenges for the quantitative detection and real-time monitoring of a controllable nanoself-assembly process due to insufficient measuring methods. Herein, we propose a new and effective fluorescence technology for realizing quantitative detection of a controllable conversion process of one-dimensional (1D)/two-dimensional (2D) nanoassemblies by introducing AIEgens as the fluorescence signal part.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!