[Assessment of the sealing ability of some root canal sealers applied using lateral condensation and single point techniques].

Ann Acad Med Stetin

Zakład Stomatologii Zachowawczej Katedry Stomatologii Zachowawczej i Endodoncji Uniwersytetu Medycznego w Łodzi, ul. Pomorska 251, 92-213 Łódź.

Published: October 2011

Aim: To evaluate the sealing ability of AH Plus, Epiphany, and EZ-Fill Root Canal Cement and to assess leakage depending on the filling technique.

Material And Methods: Eighty extracted human single-root teeth were divided into eight groups often teeth each. Thirty teeth were hand-filed to MAF 40 using a step-back technique and filled by lateral condensation with gutta-percha and AH Plus (group 1), 0.06 single point gutta-percha and AH Plus (group 2), and lateral condensation with Resilon/Epiphany (group 3). Another thirty teeth were prepared to size MAF 35 0.06 by rotary FlexMaster nickel-titanium instruments and filled using the single point technique with 0.06 Resilon/Epiphany (group 4), lateral condensation with gutta-percha and EZ-Fill cement (group 5), and 0.06 single point gutta-percha and EZ-Fill cement (group 6). The remaining twenty teeth served as positive and negative control groups. As positive control (group 7) served canals that were filed with the step-back technique and filled using lateral condensation of gutta-percha points without sealer. The negative control teeth (group 8) were left unfilled but completely covered with nail varnish. Microleakage was evaluated using a dye penetration test (2% solution of methylene blue for 72 h). The teeth were sectioned longitudinally and examined under a stereomicroscope to assess dye penetration. Differences between groups were analyzed statistically with Tamhane's test. The level of significance was taken as p < 0.05.

Results: Linear dye penetration (mean/SD) values (mm) were as follows: group 1 (1.38/2.14); group 2 (1.41/1.54); group 3 (8.98/4.55); group 4 (11.03/3.66); group 5 (1.95/2.22); group 6 (1.79/1.99). Leakage along the full length of the canal was noted in the positive control teeth and no leakage was found in negative control teeth. Tamhane's test showed that the sealing ability was lowest for Resilon/Epiphany. Leakage was highest for this material (groups 3 and 4) and was significantly higher than for teeth filled with gutta-percha combined with AH Plus or EZ-Fill. No significant differences were noted between gutta-percha with AH Plus (groups 1 and 2) and gutta-percha with EZ-Fill cement (groups 5 and 6). No significant difference in leakage existed between lateral condensation and single point groups.

Conclusions: Leakage of the dye was greatest for the Resilon/Epiphany system. The results demonstrate that the sealing technique is without influence on how well the root canals will be sealed.

Download full-text PDF

Source

Publication Analysis

Top Keywords

lateral condensation
24
single point
20
group
14
sealing ability
12
condensation gutta-percha
12
gutta-percha ez-fill
12
ez-fill cement
12
negative control
12
control teeth
12
dye penetration
12

Similar Publications

How well do empirical molecular mechanics force fields model the cholesterol condensing effect?

J Chem Phys

January 2025

School of Chemistry, University of Southampton, Highfield, Southampton SO17 1BJ, United Kingdom.

Membrane properties are determined in part by lipid composition, and cholesterol plays a large role in determining these properties. Cellular membranes show a diverse range of cholesterol compositions, the effects of which include alterations to cellular biomechanics, lipid raft formation, membrane fusion, signaling pathways, metabolism, pharmaceutical therapeutic efficacy, and disease onset. In addition, cholesterol plays an important role in non-cellular membranes, with its concentration in the skin lipid matrix being implicated in several skin diseases.

View Article and Find Full Text PDF

Aim To compare the quality of obturation using WVC (warm vertical compaction), CLC (cold lateral compaction), injectable (iFill), and Thermafil (GuttaCore) techniques, along with hydraulic condensation of bioceramic (BC) sealer, and evaluating the percentage of gutta-percha (GP), sealer, and voids in simulated internal resorptive lesions, using an advanced stereomicroscope with ImageJ software (National Institutes of Health, Bethesda, MD, USA). Methods and material In this study, 40 freshly extracted maxillary incisors were collected, and endodontic instrumentation was done to working length using hand K-files. Simulated internal resorption cavities were created in the middle-apical third of the roots after horizontal sectioning and were re-cemented.

View Article and Find Full Text PDF

This study evaluated the extent to which obturation materials bypass fractured endodontic instruments positioned in the middle and apical thirds of severely curved simulated root canals using different obturation techniques. Sixty resin blocks with simulated root canals were used, each with a 50° curvature, a 6.5 mm radius of curvature, and a length of 16.

View Article and Find Full Text PDF

Purpose: While it is common practice for schools across the United States to include neurodivergent children in physical education classes, many programs outside of school-such as those at home or in the community-are not effectively tailored to meet their support needs. This gap contributes to lower levels of physical activity among neurodivergent children. Our objective was to address this issue by systematically adapting the program to enable neurodivergent children to safely engage in physical activity at home.

View Article and Find Full Text PDF

Edge contacts offer a significant advantage for enhancing the performance of semiconducting transition metal dichalcogenide (TMDC) devices by interfacing with the metallic contacts on the lateral side, which allows the encapsulation of all of the channel material. However, despite intense research, the fabrication of feasible electrical edge contacts to TMDCs to improve device performance remains a great challenge, as interfacial chemical characterization via conventional methods is lacking. A major bottleneck in explicitly understanding the chemical and electronic properties of the edge contact at the metal-two-dimensional (2D) semiconductor interface is the small cross section when characterizing nominally one-dimensional edge contacts.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!