Municipal solid waste (MSW) landfills are potential long-term sources of emissions. Hence, they need to be managed after closure until they do not pose a threat to humans or the environment. The case study on the Breitenau MSW landfill was performed to evaluate future emission levels for this site and to illustrate the effect of final cover installation with respect to long-term environmental risks. The methodology was based on a comprehensive assessment of the state of the landfill and included analysis of monitoring data, investigations of landfilled waste, and an evaluation of containment systems. A model to estimate future emission levels was established and site-specific predictions of leachate emissions were presented based on scenario analysis. The results are used to evaluate the future pollution potential of the landfill and to compare different aftercare concepts in view of long-term emissions. As some leachable substances became available for water flow during cover construction due to a change in the water flow pattern of the waste, a substantial increase in leachate concentrations could be observed at the site (e.g. concentrations of chloride increased from 200 to 800 mg/l and of ammonia-nitrogen from 140 to about 500 mg/l). A period of intensive flushing before the final cover installation could have reduced the amount of leachable substances within the landfill body and rapidly decreased the leachate concentrations to 11 mg Cl/l and 79 mg NH(4)-N/l within 50 years. Contrarily, the minimization of water infiltration is associated with leachate concentrations in a high range for centuries (above 400 mg Cl/l and 200 mg NH(4)-N/l) with low concomitant annual emission loads (below 12 kg/year of Cl or 9 kg/year of NH(4)-N, respectively). However, an expected gradual decrease of barrier efficiency over time would be associated with higher emission loads of 50 kg of chloride and 30 kg of ammonia-nitrogen at the maximum, but a faster decrease of leachate concentration levels.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.wasman.2011.02.022 | DOI Listing |
Polymers (Basel)
December 2024
Dipartimento di Meccanica, Matematica e Management, Politecnico di Bari, 70100 Bari, Italy.
High volumetric shrinkage and rheological behavior of polypropylene (PP) are the main problems that make material extrusion (MEX) uncommon for this material. The complexity is raised when recycled materials are used. This research covered different aspects of the MEX process of virgin and recycled PP, from the analysis of rough materials to the mechanical evaluation of the final products.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081, China.
The most time-consuming aspect of dental prosthesis installation is the osseointegration of a metal implant with bone tissue. The acceleration of this process may be achieved through the use of extracorporeal shock wave therapy. The objective of this study is to investigate the conditions for osseointegration of the second premolar implant in the mandibular segment through the use of a poroelastic model implemented in the movable cellular automaton method.
View Article and Find Full Text PDFInt J Mol Sci
December 2024
Pre-Clinical Research Centre, Wrocław Medical University, Marcinkowskiego 1, 50-368 Wrocław, Poland.
Percutaneous Coronary Intervention (PCI) is a treatment method that involves reopening narrowed arteries with a balloon catheter that delivers a cylindrical, mesh-shaped implant device to the site of the stenosis. Currently, by applying a coating to a bare metal stent (BMS) surface to improve biocompatibility, the main risks after PCI, such as restenosis and thrombosis, are reduced while maintaining the basic requirements for the mechanical behavior of the stent itself. In this work, for the first time, the development and optimization process of the spatial structure of the Co-Cr stent (L-605) with a graphene-based coating using cold-wall chemical vapor deposition (CW-CVD) to ensure uniform coverage of the implant was attempted.
View Article and Find Full Text PDFBioengineering (Basel)
December 2024
Department of Computer Engineering, Gachon University, Seongnam 13120, Republic of Korea.
This study proposes a new hybrid machine learning (ML) model for the early and accurate diagnosis of heart disease. The proposed model is a combination of two powerful ensemble ML models, namely ExtraTreeClassifier (ETC) and XGBoost (XGB), resulting in a hybrid model named ETCXGB. At first, all the features of the utilized heart disease dataset were given as input to the ETC model, which processed it by extracting the predicted probabilities and produced an output.
View Article and Find Full Text PDFBioengineering (Basel)
December 2024
Department of Biomedical Engineering, The Hong Kong Polytechnic University, Hong Kong SAR 999077, China.
Background: Orthotic treatment is a well-acknowledged conservative treatment for moderate adolescent idiopathic scoliosis (AIS). The efficacy of this treatment is significantly determined by the forces applied to the bodies of patients. However, there is uncertainty regarding the optimal force levels that should be applied to the patient's torso by spinal orthosis.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!