AI Article Synopsis

  • The study demonstrates a new method for attaching oligoethylene oxide compounds to surfaces to reduce nonspecific protein adsorption, which is crucial for sensors and membranes in biological applications.
  • The research reveals that these modified surfaces (EO(3)-Si(x)N(4) and EO(6)-Si(x)N(4)) show significantly lower protein adsorption rates compared to traditional coatings, achieving values as low as 0.08 mg m(-2).
  • Characterization techniques confirm the stability and effectiveness of these coatings in harsh conditions, indicating their potential for broader applications in biomedical fields.

Article Abstract

The grafting of polymers and oligomers of ethylene oxide onto surfaces is widely used to prevent nonspecific adsorption of biological material on sensors and membrane surfaces. In this report, we show for the first time the robust covalent attachment of short oligoethylene oxide-terminated alkenes (CH(3)O(CH(2)CH(2)O)(3)(CH(2))(11)-(CH═CH(2)) [EO(3)] and CH(3)O(CH(2)CH(2)O)(6)(CH(2))(11)-(CH═CH(2)) [EO(6)]) from the reaction of alkenes onto silicon-rich silicon nitride surfaces at room temperature using UV light. Reflectometry is used to monitor in situ the nonspecific adsorption of bovine serum albumin (BSA) and fibrinogen (FIB) onto oligoethylene oxide coated silicon-rich silicon nitride surfaces (EO(n)-Si(x)N(4), x > 3) in comparison with plasma-oxidized silicon-rich silicon nitride surfaces (SiO(y)-Si(x)N(4)) and hexadecane-coated Si(x)N(4) surfaces (C(16)-Si(x)N(4)). A significant reduction in protein adsorption on EO(n)-Si(x)N(4) surfaces was achieved, adsorption onto EO(3)-Si(x)N(4) and EO(6)-Si(x)N(4) were 0.22 mg m(-2) and 0.08 mg m(-2), respectively. The performance of the obtained EO(3) and EO(6) layers is comparable to those of similar, highly protein-repellent monolayers formed on gold and silver surfaces. EO(6)-Si(x)N(4) surfaces prevented significantly the adsorption of BSA (0.08 mg m(-2)). Atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), X-ray reflectivity and static water contact angle measurements were employed to characterize the modified surfaces. In addition, the stability of EO(6)-Si(x)N(4) surfaces in phosphate-buffered saline solution (PBS) and alkaline condition (pH 10) was studied. Prolonged exposure of the surfaces to PBS solution for 1 week or alkaline condition for 2 h resulted in only minor degradation of the ethylene oxide moieties and no oxidation of the Si(x)N(4) substrates was observed. Highly stable antifouling coatings on Si(x)N(4) surfaces significantly broaden the application potential of silicon nitride-coated microdevices, and in particular of microfabricated filtration membranes.

Download full-text PDF

Source
http://dx.doi.org/10.1021/am100985cDOI Listing

Publication Analysis

Top Keywords

silicon nitride
16
nitride surfaces
16
surfaces
14
silicon-rich silicon
12
oligoethylene oxide
8
ethylene oxide
8
nonspecific adsorption
8
sixn4 surfaces
8
008 m-2
8
eo6-sixn4 surfaces
8

Similar Publications

In situ electrochemical liquid phase transmission electron microscopy (LP-TEM) measurements utilize micro-chip three-electrode cells with electron transparent silicon nitride windows that confine the liquid electrolyte. By imaging electrocatalysts deposited on micro-patterned electrodes, LP-TEM provides insight into morphological, phase structure, and compositional changes within electrocatalyst materials under electrochemical reaction conditions, which have practical implications on activity, selectivity, and durability. Despite LP-TEM capabilities becoming more accessible, in situ measurements under electrochemical reaction conditions remain non-trivial, with challenges including electron beam interactions with the electrolyte and electrode, the lack of well-defined experimental workflows, and difficulty interpreting particle behavior within a liquid.

View Article and Find Full Text PDF

Azo-PMA nanopores of sub-20 nm length for unimolecular resolution of nucleic acids and proteins.

Talanta

December 2024

Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences & Chongqing School, University of Chinese Academy of Science, Chongqing, 400714, PR China. Electronic address:

Owing to the facile fabrication and surface modification, the cost-effective polymer nanopores are widely employed in unimolecular determination of biomacromolecules and selective sensing of small molecules, nanoparticles and biomarkers. However, the documented polymer nanochannels are generally microscale in length with low spatial resolution. We herein synthesized azobenzene side-chain polymer (Azo-PMA) and spin-coated on silicon nitride membrane to obtain a polymer film of nanoscale thickness for further nanopore generation via controlled dielectric breakdown (CDB) approach.

View Article and Find Full Text PDF

3DCryoHolder: a new open access 3D printable system to store and transport silicon nitride membranes under cryogenic conditions for spectromicroscopy at low temperature.

J Synchrotron Radiat

January 2025

Polimero eta Material Aurreratuak: Fisika, Kimika eta Teknologia, Kimika Fakultatea, Euskal Herriko Unibertsitatea UPV/EHU, Donostia-San Sebastian 20018, Spain.

Data acquisition under cryogenic conditions allows one to avoid unwanted damage caused by beam irradiation. This is particularly important for the study of biological samples at hard X-ray, micro- or nano-probe beamlines, which focus synchrotron radiation to small beam sizes with extremely high flux densities. Sample preparation methods for cryopreserved specimens have been adapted from electron microscopy, and include the use of silicon nitride membranes as they are easy to handle and possess low X-ray absorption.

View Article and Find Full Text PDF

Single-molecule fluorescence spectroscopy offers unique capabilities for the low-concentration sensing and probing of molecular dynmics. However, employing such a methodology for versatile sensing and diagnostics under point-of-care demands device miniaturization to lab-on-a-chip size. In this study, we numerically design metalenses with high numerical aperture (NA = 1.

View Article and Find Full Text PDF

Advances, Challenges, and Applications of Graphene and Carbon Nanotube-Reinforced Engineering Ceramics.

Nanomaterials (Basel)

November 2024

Institute for Technical Physics and Materials Science, HUN-REN Centre for Energy Research, Konkoly-Thege Miklós Str. 29-33, 1121 Budapest, Hungary.

Engineering ceramics and their composites are widely used owing to their excellent properties, including high wear, corrosion and heat resistance, low friction coefficient, and low thermal conductivity; thus, the current paper presents a comprehensive review of the most common types of engineering ceramics, demonstrating their key properties, advantages, potential applications, and challenges. This paper also provides prevailing methods for tackling the engineering ceramic challenges and maximizing their applicability. This review paper focuses on alumina (AlO), silicon carbide (SiC), zirconia (ZrO), aluminum nitride (AlN), and silicon nitride (SiN), and explores their usability in automotive, aerospace, and tribological applications.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!