In this work, a novel electrochemical nitrite sensor for sensitive determination of nitrite based on poly(alizarin red S)-multi-wall carbon nanotubes (PARS-MWNTs) composite film on the glassy carbon electrode was described. The surface morphologies of different electrodes were characterized by scanning electron microscopy. Cyclic voltammetry, chronocoulometry and linear sweep voltammetry were used to investigate the electrochemical response and oxidation mechanism of nitrite at the PARS-MWNTs composite film based sensor. The experimental parameters were optimized, such as electropolymerization pH value, film thickness and detection pH value et al. Under optimal working conditions, the oxidation peak current of nitrite linearly increased with its concentration in the range of 30 nM to 1.1 mM with a low detection limit of 2 nM. The PARS-MWNTs composite film based nitrite sensor was applied to the determination of nitrite in sausage, and the good recovery indicated that it may have practical applications in nitrite monitoring system.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1166/jnn.2010.2534 | DOI Listing |
Nanotechnology
January 2025
Universiti Teknologi PETRONAS, Centre of Innovative Nanostructures and Nanodevices (COINN), Universiti Teknologi PETRONAS, 32610 Seri Iskandar, Perak Darul Ridzuan, MALAYSIA, Seri Iskandar, Perak, 32610, MALAYSIA.
Most previously reported susceptors for microwave welding are in powder form. In this study, a thin-film susceptor was employed due to its uniform heating rate and ease of handling. Silicon carbide nanowhisker (SiCNW) were incorporated into a poly(methyl methacrylate) (PMMA) matrix to create a nanocomposite thin film, which served as the susceptor.
View Article and Find Full Text PDFNano Lett
January 2025
Department of Materials Science and Engineering, Yonsei University, Seoul 03722, Republic of Korea.
Achieving low thermal conductivity and high mechanical strength presents a material design challenge due to intrinsic trade-offs, such as the aerogel's porosity, impeding applications in construction, industry, and aerospace. This study presents a composite that incorporates a silica aerogel within a thermally expanded 2D layered vermiculite matrix. This design overcomes limitations imposed by van der Waals bonding lengths, typically less than 10 Å, which hinder aerogel integration with van der Waals crystals.
View Article and Find Full Text PDFTurk J Chem
November 2024
School of Chemical and Blasting Engineering, Anhui University of Science and Technology, Huainan, P.R. China.
The development of ultraviolet (UV) shielding materials is of great importance to protect human health and prevent the degradation of organic matter. However, the synthesis of highly efficient UV shielding polymer nanocomposites is currently limited by the agglomeration of inorganic anti-UV nanoparticles (NPs) within the polymer matrix and the limited absorption spectrum of UV shielding agents. In this study, highly effective manganese doped carbon quantum dots@halloysite nanotube composites (Mn-CDs@HNTs/PAS) were successfully synthesized by loading manganese-doped carbon quantum dots (Mn-CDs) into UV shielding effective halloysite nanotubes (HNTs) via the solvothermal method, followed by polymerization modification (PAS).
View Article and Find Full Text PDFCarbohydr Polym
March 2025
Institute of Oncology, Guangxi Academy of Medical Sciences and the People's Hospital of Guangxi Zhuang Autonomous Region, Nanning 530021, China. Electronic address:
The development of safe, environmentally friendly, edible antimicrobial packaging films represents a promising alternative to conventional plastic packaging for reducing spoilage and extending the shelf life of fresh food. Here, we propose a novel strategy to construct edible β-CD-MOF/carvacrol@zein (BCCZ) composite films by intertwining β-CD-MOF loaded with the antimicrobial essential oil carvacrol, and zein. The resulting BCCZ films exhibit high humidity-triggered, long-lasting bactericidal efficacy, effective fruit preservation, and excellent biosafety.
View Article and Find Full Text PDFNanomicro Lett
January 2025
Department of Chemical Engineering, The Pennsylvania State University, University Park, PA, 16802, USA.
Plant cell wall (CW)-like soft materials, referred to as artificial CWs, are composites of assembled polymers containing micro-/nanoparticles or fibers/fibrils that are designed to mimic the composition, structure, and mechanics of plant CWs. CW-like materials have recently emerged to test hypotheses pertaining to the intricate structure-property relationships of native plant CWs or to fabricate functional materials. Here, research on plant CWs and CW-like materials is reviewed by distilling key studies on biomimetic composites primarily composed of plant polysaccharides, including cellulose, pectin, and hemicellulose, as well as organic polymers like lignin.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!