The medial-lateral force distribution in the ovine stifle joint during walking.

J Orthop Res

Julius Wolff Institute, Charité - Universitätsmedizin Berlin, Berlin-Brandenburg Center for Regenerative Therapies (BCRT), Centrum für Sportwissenschaft und Sportmedizin Berlin (CSSB), Berlin, Germany.

Published: April 2011

Knowledge of the load distribution in the knee is essential for understanding the interaction between mechanics and biology in both the healthy and diseased joint. While the sheep stifle joint is a predominant model for better understanding regeneration after injury, little is known about the compartmental force distribution between the medial and lateral condyles. By including sheep specific anatomy and gait analyses, we used computational musculoskeletal analyses to estimate the medial-lateral joint contact force distribution in ovine stifle joints during walking by simplifying the system of equations into a 2D problem that was solved directly. Gait analysis was conducted using bone markers in three female Merino-mix sheep. Joint contact forces were computed with respect to the specific anatomy of the ovine tibia, resulting in low (<0.13 bodyweight) mean anteroposterior shear forces throughout the gait cycle, with mean peak contact forces perpendicular to the tibial plateau of 2.2 times bodyweight. The medial-lateral compartmental load distribution across the tibial condyles was determined and revealed loading predominantly on the medial condyle, bearing approximately 75% of the total load during phases of peak loading. By considering the anatomical characteristics of the ovine stifle joint, together with the dynamic forces during gait, this study provides evidence for predominantly medial loading in sheep, somewhat similar to the distribution reported in man. However, the exact conditions under which the loading in the ovine stifle joint is representative of the human situation will need to be elucidated in further studies.

Download full-text PDF

Source
http://dx.doi.org/10.1002/jor.21254DOI Listing

Publication Analysis

Top Keywords

force distribution
12
distribution ovine
8
ovine stifle
8
stifle joint
8
specific anatomy
8
joint contact
8
joint
5
medial-lateral force
4
distribution
4
joint walking
4

Similar Publications

Accurate models for predicting drop dynamics, such as maximum drop departure sizes, are crucial for estimating heat transfer rates during condensation on superhydrophobic (SH) surfaces. Previous studies have focused on examining the heat transfer rates for SH surfaces under the influence of gravity or vapor flowing over the surface. This study investigates the impact of surface solid fraction and texture scale on drop mobility in a condensing environment with a humid air flow.

View Article and Find Full Text PDF

Objective: The complex mix of factors, including hemodynamic forces and wall remodeling mechanisms, that drive intracranial aneurysm growth is unclear. This study focuses on the specific regions within aneurysm walls where growth occurs and their relationship to the prevalent hemodynamic conditions to reveal critical mechanisms leading to enlargement.

Methods: The authors examined hemodynamic models of 67 longitudinally followed aneurysms, identifying 88 growth regions.

View Article and Find Full Text PDF

Analysis of the Feasibility of the OrthoNail Hybrid Intramedullary Implant in the Human Body with Respect to Material Durability.

J Funct Biomater

January 2025

Department of Mechanics, Materials and Biomedical Engineering, Faculty of Mechanical Engineering, Wrocław University of Science and Technology, Smoluchowskiego 25, 50-372 Wrocław, Poland.

This study focuses on the development and evaluation of the OrthoNail hybrid intramedullary implant for lower limb lengthening in patients requiring significant skeletal reconstruction. The implant addresses the challenges in load-bearing during rehabilitation, providing a robust solution that is capable of supporting physiological loads. Mechanical tests, including axial compression, tension, torsion, and 3,4-point bending, determined the implant's load capacity and fatigue resistance, while finite element analysis assessed stress distributions in bone tissue and around screw holes during single-leg stance, with boundary conditions derived from Orthoload database data.

View Article and Find Full Text PDF

This study evaluated the potential usage of phosphorylated egg white protein (P-EWP) nanogels fabricated via microwave-induced phosphorylation modification and gel process and further ultrasonic nanometrization as novel delivery systems for cinnamon bark essential oil (CBEO). Compared to EWP-CBEO nanogels without chemical phosphorylation, the obtained P-EWP-CBEO nanogels have shown smaller average hydrodynamic diameter (133.6 nm), relatively uniform size distribution (polydispersity index around 0.

View Article and Find Full Text PDF

An Open-Source 3D Printed Three-Fingered Robotic Gripper for Adaptable and Effective Grasping.

Biomimetics (Basel)

January 2025

Department of Mechanical Engineering, Sungkyunkwan University, 2066 Seobu-ro, Jangan-gu, Suwon 16419, Republic of Korea.

This research focuses on the design of a three-finger adaptive gripper using additive manufacturing and electromechanical actuators, with the purpose of providing a low-cost, efficient, and reliable solution for easy integration with any robot arm for industrial and research purposes. During the development phase, 3D printing materials were employed in the gripper's design, with Polylactic Acid (PLA) filament used for the rigid mechanical components and Thermoplastic Polyurethane (TPU) for the flexible membranes that distribute pressure to the resistive force sensors. Stress analysis and simulations were conducted to evaluate the performance of the components under load and to gradually refine the design of the adaptive gripper.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!