Objectives: The aim of this study was to assess how different shades of try-in pastes, uncured and cured resin cements influence the overall color of porcelain veneer restorations.

Methods: Porcelain veneers of shade Vita 1M1 VM7 and 1mm thick were applied to bovine teeth using three shades of resin cement and their try-in paste produced by three manufacturers. Analysis of variance was carried out on the color difference values (ΔE*) between the Aquagel and both the try-in paste and cured resins. An assessment of the clinical significance of ΔE* between the try-in paste and the cured resin and also between the uncured and cured resin was made.

Results: There were statistically significant differences in veneers' colors when using different shades of both Calibra and Nexus resin cements (p<0.05). Also, statistically significant differences were noticed when using different shades of both Rely-X and Nexus try-in pastes (p<0.05). Color differences produced between the try-in pastes and the corresponding shades of cured resin cements ranged from ΔE* 1.05 to 3.34. The color differences between uncured and cured resins of the same shade ranged from ΔE* 0.78 to 1.41.

Conclusions: Different colored try-in pastes and resin cements produced color changes which are clinically useful in changing the color of veneer restorations and therefore aid color matching to adjacent dentition. Clinically significant differences were found between try-in pastes and the cured resin of the same shade, however, there were relatively small changes measured between uncured and cured resins. The color match achieved by the try-in paste has to be treated with caution and further assessment of the restoration made with the resin in place before curing is recommended.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jdent.2010.08.013DOI Listing

Publication Analysis

Top Keywords

cured resin
16
uncured cured
12
resin cements
12
try-in paste
12
try-in pastes
8
pastes uncured
8
paste cured
8
resin
6
cured
5
investigation try-in
4

Similar Publications

The Effect of Plaque Detectors on the Color Stability of Two Types of Restorative Materials.

J Esthet Restor Dent

January 2025

Department of Biomedical and Neuromotor Science (DIBINEM), Alma Mater Studiorum, University of Bologna, Bologna, Italy.

Objective: To investigate the color stability of a one-shade resin-based composite material (RC) and a glass-ionomer cement (GIC) after staining with plaque detectors (PDs) with different formulations and delivery forms.

Materials And Methods: Rectangular-shaped specimens (7 × 3 × 2 mm) were produced with RC (Venus Diamond One, Kulzer) and GIC (Fujy IX GP, GC) (n = 30). Further, the following PDs were used on the specimens: (1) tablets (T; Plaq-Search, TePe); (2) mouthwash (M; Plaque Agent, Miradent); and (3) light-curing liquid (L; Plaque test, Ivoclar).

View Article and Find Full Text PDF

Direct printed aligners (DPAs) offer benefits like the ability to vary layer thickness within a single DPA and to 3D print custom-made removable orthodontic appliances. The biocompatibility of appliances made from Tera Harz TA-28 (Graphy Inc., Seoul, South Korea) depends on strict adherence to a standardized production and post-production protocol, including UV curing.

View Article and Find Full Text PDF

In this paper, alumina-modified wood liquefaction (AL-WP) was prepared by blending nano-alumina (AlO) into wood liquefaction phenolic resin (WP) using a co-blending method. Alumina-modified wood liquefaction protofilament fiber (AL-WPF) was obtained by melt-spinning, curing, and thermo-curing processes, which were followed by carbonization to obtain alumina-modified wood liquefaction carbon fiber (AL-WCF). This paper focuses on the enhancement effect of nano-alumina doping on the mechanical properties and heat resistance of wood liquefaction carbon fiber (WCF), explores the evolution of graphite microcrystalline structure during the high-temperature carbonization process, and optimizes the curing conditions of AL-WPF.

View Article and Find Full Text PDF

The key structural components of a wind turbine blade, such as the skin, spar cap, and shear web, are fabricated from fiber-reinforced composite materials. The spar, predominantly manufactured via resin infusion-a process of resin injection and curing in carbon fibers-is prone to initial defects, such as pores, wrinkles, and delamination. This study suggests employing the pultrusion technique for spar production to consistently obtain a uniform cross-section and augment the reliability of both the manufacturing process and the design.

View Article and Find Full Text PDF

Epoxy nanocomposites are widely used in various applications because of their excellent properties. Different types of manufacturing techniques are used to produce epoxy composites based on various fillers, molecular weight, and applications required. The physical properties and chemical structure of epoxy resin help in determining the method for its manufacturing.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!