Comparative effect of chlorhexidine and some mouthrinses on bacterial biofilm formation on titanium surface.

Curr Microbiol

Department of Biomolecular Science, Division of Toxicological, Hygienistic and Environmental Sciences, University of Urbino Carlo Bo, Via Santa Chiara, 27, Urbino, Italy.

Published: February 2011

The aim of the present study was to evaluate the effectiveness of chlorhexidine digluconate (CHX) and commonly used mouthrinses to single- and poly-species biofilms by S. mutans, S. aureus and P. aeruginosa, on titanium discs of grade IV. The formation of single- and poly-species biofilms at 16.5, 40.5 and 64.5-h incubation on titanium surface was evaluated by plate count (CFU ml⁻¹) before and after exposure to CHX and four mouthrinses (Curasept, Listerine, Meridol and Buccagel) and expressed as percentage of Inhibitory Activity (IA%). The application of the different anti-plaque formulations on biofilm can reduce the adhesion of bacteria to titanium surface with different degrees. The higher efficacy was observed for Listerine that shows IA% = 100 on the biofilm formed by S. mutans at 16.5 h. Log count of CFU was dependent to culture time and four mouthrinses for S. mutans and S. aureus, whilst was not dependent to culture time but to mouthrinses for P. aeruginosa. In general, the efficacy was particularly lesser to poly-species biofilms; no statistical differences were evidenced between all the mouthrinses and CHX as control group. The tested mouthrinses, compared to reference CHX 0.2%, have demonstrated a significant lower antibacterial activity than Listerine towards the experimental biofilms. This "in vitro" biofilm model should prove extremely useful for pre-clinical testing of anti-plaque agents, which inhibit biofilm formation, can prevent subsequent implant failure.

Download full-text PDF

Source
http://dx.doi.org/10.1007/s00284-010-9727-xDOI Listing

Publication Analysis

Top Keywords

titanium surface
12
poly-species biofilms
12
biofilm formation
8
single- poly-species
8
mutans aureus
8
count cfu
8
dependent culture
8
culture time
8
time mouthrinses
8
mouthrinses
7

Similar Publications

A Quantitative Chemometric Study of Pharmaceutical Tablet Formulations Using Multi-Spectroscopic Fibre Optic Probes.

Pharmaceuticals (Basel)

December 2024

College of Science and Engineering, Flinders University, Bedford Park, South Australia 5042, Australia.

Two fibre optic probes were custom designed to perform Raman and near-infrared spectroscopic measurements. Our long-term objective is to develop a non-destructive tool able to collect data in hard-to-access locations for real-time analysis or diagnostic purposes. This study evaluated the quantitative performances of Probe A and Probe B using model pharmaceutical tablets.

View Article and Find Full Text PDF

Biosynthesis and Characterization of Silver Nanoparticles and Simvastatin Association in Titanium Biofilms.

Pharmaceuticals (Basel)

November 2024

Laboratório de Farmacologia de Antimicrobianos e Microbiologia, Faculdade de Ciências Farmacêuticas, Universidade Estadual de Campinas (UNICAMP), Campinas 13083-970, Brazil.

Introduction: Simvastatin is an antilipidemic drug that has already demonstrated antibacterial activities on oral and non-oral microorganisms. Silver nanoparticles also exhibit antimicrobial properties, particularly for coating implant surfaces. In this study, we evaluated the effects of combining simvastatin with silver nanoparticles on the formation and viability of biofilms consolidated on titanium discs.

View Article and Find Full Text PDF

This study evaluates the effects of laser parameters on the surface remelting of the Ti-3Al-2.5V alloy. A ms-laser equipped with a coaxial gas-pressure head integrated into a Swiss-type turning machine is used for the laser remelting process of cylindrical parts.

View Article and Find Full Text PDF

Determination of the Minimum Uncut Chip Thickness of Ti-6Al-4V Titanium Alloy Based on Dead Metal Zone.

Micromachines (Basel)

November 2024

Key Laboratory of Rapid Development & Manufacturing Technology for Aircraft, Shenyang Aerospace University, Ministry of Education, Shenyang 110136, China.

In Ti-6Al-4V titanium alloy micro-machining, since the uncut chip thickness (UCT) is comparable to the radius of the tool cutting edge, there exists a minimum uncut chip thickness (MUCT), and when the UCT is smaller than the MUCT, the plowing effect dominates the cutting process, which seriously affects the machined surface quality and tool life. Therefore, the reliable prediction of the MUCT is of great significance. This paper used Deform to establish an orthogonal cutting simulation model, studied the effect of the dead metal zone (DMZ) on the micro-cutting material flow, determined the DMZ range, and proposed a new method for determining the MUCT based on the DMZ.

View Article and Find Full Text PDF

Difficult-to-cut titanium matrix composites (TMCs) are widely used in the aerospace, automotive, and defense sectors due to their excellent physical properties. Electrochemical mill grinding (ECMG) can achieve the processing effects of electrochemical milling and electrochemical grinding using the same tool, which has the potential to complete the rough and finish machining of TMCs in succession. However, in the rough machining stage, the bottom of the slot becomes concave due to the inevitable stray corrosion, leading to poor flatness, which increases the machining allowance for subsequent finish machining.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!