Three-year clinical evaluation of two flowable composites.

Quintessence Int

Louisiana State University Health Sciences Center, School of Dentistry, New Orleans, Louisiana 70119, USA.

Published: June 2010

Objective: To evaluate the clinical efficacy of two flowable composite resins used to restore occlusal caries lesions. Tetric Flow (Vivadent) and Esthet-X Flow (Dentsply/Caulk) are composite resins with decreased filler loading (Tetric Flow: 67% filler by weight, 43% by volume; Esthet-X Flow: 61% filler by weight, 53% by volume) and lower viscosity compared to conventional composite resins.

Method And Materials: Sixty-three teeth with occlusal caries were randomly assigned to calibrated practitioners who placed occlusal restorations (32 for Esthet-X Flow; 31 for Tetric Flow). After tooth preparation and caries removal, each material was inserted. A polyvinyl impression was made of each preparation and measured to record the preparation size. Prime and Bond NT (Dentsply/Caulk) was used to bond both flowable composites, which were incrementally placed and light cured for 20 seconds. Each restoration was evaluated at baseline (1 week after restoration placement) and 3, 6, 12, and 36 months for marginal discoloration, secondary caries, anatomical form, retention, polishability, marginal adaptation, and color match. Groups were compared at 3 years and the data analyzed statistically with a .05 level of significance using generalized estimating equations, with size of restoration compared to the modified Ryge criteria.

Results: Of the effects that were estimable, only color match exhibited a difference between treatment groups (P = .0467, favoring Esthet-X Flow). No other differences were observed between materials. Although no difference was observed between groups, marginal discoloration (P = .0164) and marginal adaptation (P = .0001) significantly worsened at 36 months. For polishability, a significant difference was observed at 36 months (P = .0066). No other outcomes changed significantly over time. Size of the restoration was found to be positively associated with worse outcome for color match (P = .0062 for area; P = .0439 for volume).

Conclusion: Although flowable composite resins are advocated for occlusal restorations, this study suggests that they should be limited to small restorations such as preventive resin restorations having isthmus widths of one-quarter or less of intercuspal distance.

Download full-text PDF

Source

Publication Analysis

Top Keywords

esthet-x flow
16
composite resins
12
tetric flow
12
color match
12
flowable composites
8
flowable composite
8
occlusal caries
8
filler weight
8
occlusal restorations
8
marginal discoloration
8

Similar Publications

Introduction: Resin-based composites (RBCs), as restorative dental materials, have given a new dimension to conservative and esthetic dentistry. The objective of the present study is to evaluate and compare the depth of cure of RBC's for posterior use: Sculptable bulk-fill composite - Tetric N-Ceram bulk fill (TNCBF), Flowable bulk-fill composites-TetricEvoflow bulk fill (TEFBF), Surefil SDR bulk fill (SDRBF), Dual cure bulk fill-Fill-Up (FDCBF) with conventional RBC-Esthet-X flow (EXF) and Filtex Z250 (FZ).

Materials And Methods: A standardized polyacrylic mold was bulk filled with each of the six composites and light-cured for 20 s, followed by 24 h storage in water.

View Article and Find Full Text PDF

Polymerization shrinkage and shrinkage force kinetics of high- and low-viscosity dimethacrylate- and ormocer-based bulk-fill resin composites.

Odontology

January 2019

Department of Preventive Dentistry, Periodontology and Cariology, Center for Dental Medicine, University of Zurich, Plattenstrasse 11, 8032, Zurich, Switzerland.

The aim of the present study was to investigate polymerization shrinkage, shrinkage force development, and degree of monomer conversion of high- and low-viscosity dimethacrylate- and ormocer-based bulk-fill resin composites. Two flowable bulk-fill composites (SDR, x-tra base), two high-viscosity bulk-fill composites (Bulk Ormocer, SonicFill), and two conventional composite materials (Esthet X flow, Esthet X HD) were photoactivated for 20 s at 1275 mW/cm. Linear polymerization shrinkage and shrinkage force were recorded in real time using custom-made devices, and the force rate and time to achieve maximum force rate were determined.

View Article and Find Full Text PDF

Effect of Salivary pH on Color Stability of Different Flowable Composites - A Prospective In-vitro Study.

J Clin Diagn Res

October 2016

Professor and Head of Department, Department of Conservative Dentistry and Endodontics, M.P Dental College and Hospital, Mujmahuda, Vadodara, Gujarat, India .

Introduction: Scientifically and clinically there has been lot of development in the field of aesthetic dentistry. However, there is limited or restricted information regarding the color stability of flowable composite materials.

Aim: The aim of this study was to evaluate the spectrophotometric color stability of three different flowable composite materials with respect to three different pH of saliva.

View Article and Find Full Text PDF

Monomer conversion and shrinkage force kinetics of low-viscosity bulk-fill resin composites.

Acta Odontol Scand

August 2015

Department of Endodontics and Restorative Dentistry, School of Dental Medicine, University of Zagreb, Zagreb , Croatia.

Objective: To investigate the subsurface degree of conversion (DC) and shrinkage force formation of low-viscosity (flowable) bulk-fill composite materials.

Materials And Methods: Three flowable bulk-fill resin composites [SureFil SDR flow (SDR; Dentsply DeTrey), Venus Bulk Fill (VB; Heraeus Kulzer) and x-tra base (XB; VOCO)] and one conventional flowable control composite material [EsthetX flow (EX; Dentsply DeTrey)] were tested. The materials were photoactivated for 20 s at an irradiance of 1170 mW/cm2 and the DC (n=5) was recorded at 0.

View Article and Find Full Text PDF

Effect of modulated photo-activation on polymerization shrinkage behavior of dental restorative resin composites.

Eur J Oral Sci

August 2014

Department of Preventive Dentistry, Periodontology and Cariology, Center for Dental Medicine, University of Zurich, Zurich, Switzerland.

This study investigated the influence of modulated photo-activation on axial polymerization shrinkage, shrinkage force, and hardening of light- and dual-curing resin-based composites. Three light-curing resin composites (SDR bulk-fill, Esthet X flow, and Esthet X HD) and one dual-curing material (Rebilda DC) were subjected to different irradiation protocols with identical energy density (27 J cm(-2) ): high-intensity continuous light (HIC), low-intensity continuous light (LIC), soft-start (SS), and pulse-delay curing (PD). Axial shrinkage and shrinkage force of 1.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!