With an interest in finding the fragility for a simple, single component, molecular glassformer, we have determined the dielectric relaxation and glass transition behavior for a series of glasses in the CS(2)-S(2)Cl(2) and CS(2)-toluene systems. Crystallization of CS(2) can be completely avoided down to the composition 20 mol% second component, and the fragility proves almost independent of CS(2) content in each system. Since the glass temperature T(g) obtained from both thermal studies and from dielectric relaxation (using T(g,diel)=T(tau=100 s)) is quite linear over the whole composition range in each system, and since relaxation time data for pure CS(2) fall on the same master plot when scaled by the linearly extrapolated T(g) value, we deduce that pure CS(2) has the same high fragility as the binary solutions. The value is m=86, as for ortho-terphenyl (OTP). Based on observations of independent studies for the vibrational density of states (VDoS) (of inherent structures for OTP and instantaneous, at-temperature structures for CS(2)), we attribute the high fragility to an excess vibrational heat capacity (defined by C(p) (vib, excess)=dS(vib, excess)/d ln T) originating in the behavior of the low frequency modes of the VDoS (the boson peak modes). Both low frequency DoS and anharmonicity increase with increasing temperature, augmenting the configurational entropy drive to the top of the system energy landscape. The surprising implication is that fragility is determined in the vibrational, not configurational, manifold of microstates.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1063/1.3380833 | DOI Listing |
Materials (Basel)
December 2024
Department of Non-Ferrous Metals, AGH University of Science and Technology, 30-059 Krakow, Poland.
The aim of this study was to compare the mechanical properties of carbon-fiber-reinforced polymer (CFRP) composites produced using three popular technologies. The tests were performed on composites produced from prepregs in an autoclave, the next variant is composites produced using the infusion method, and the third variant concerns composites produced using the vacuum-assisted hand lay-up method. For each variant, flat plates with dimensions of 1000 mm × 1000 mm were produced while maintaining similar material properties and fabric arrangement configuration.
View Article and Find Full Text PDFPolymers (Basel)
January 2025
Micron School of Material Science and Engineering, Boise State University, Boise, ID 83725, USA.
Carbon-fiber composites with thermoplastic matrices offer many processing and performance benefits in aerospace applications, but the long relaxation times of polymers make it difficult to predict how the structure of the matrix depends on its chemistry and how it was processed. Coarse-grained models of polymers can enable access to these long-time dynamics, but can have limited applicability outside the systems and state points that they are validated against. Here we develop and validate a minimal coarse-grained model of the aerospace thermoplastic poly(etherketoneketone) (PEKK).
View Article and Find Full Text PDFPolymers (Basel)
January 2025
State Key Laboratory of Chemical Safety, Qingdao 266000, China.
Polyurea (PUR) has been widely used as a protective coating in recent years. In order to complete the understanding of the relationship between PUR microstructure and its energy absorption capabilities, the mechanical and dynamic performance of PURs containing various macrodiol structural units were compared using material characterization techniques and molecular dynamic simulation. The results showed that the PUR polycarbonate diols formed as energy absorbing materials showed high tensile strength, high toughness, and excellent loss factor distribution based on the comparison of stress-strain tensile curves, glass transition temperatures, phase images, and dynamic storage loss modulus.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
Department of Chemical Engineering, Materials, Environment, Sapienza University of Rome, 00184 Rome, Italy.
Cleavable bio-based epoxy resin systems are emerging, eco-friendly, and promising alternatives to the common thermoset ones, providing quite comparable thermo-mechanical properties while enabling a circular and green end-of-life scenario of the composite materials. In addition to being designed to incorporate a bio-based resin greener than the conventional fully fossil-based epoxies, these formulations involve cleaving hardeners that enable, under mild thermo-chemical conditions, the total recycling of the composite material through the recovery of the fiber and matrix as a thermoplastic. This research addressed the characterization, processability, and recyclability of a new commercial cleavable bio-resin formulation (designed by the R-Concept company) that can be used in the fabrication of fully recyclable polymer composites.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
A.M. Butlerov Chemical Institute, Kazan Federal University, Kazan 420008, Russia.
This article is devoted to the development of a new method for the synthesis of magnetic cobalt boride nanoparticles using a low-energy approach. The obtained nanoparticles were used to create composite materials based on industrial thermoplastic ABS. The effect of different concentrations of nanoparticles on the physical, mechanical, magnetic, and dielectric properties of composite materials was studied.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!