Distribution of (1->4)-beta-galactans, arabinogalactan proteins, xylans and (1->3)-beta-glucans in tracheid cell walls of softwoods.

Tree Physiol

School of Biological Sciences, University of Auckland, Private Bag 92019, Auckland Mail Centre, Auckland 1142, New Zealand.

Published: June 2010

Polysaccharides were located in the walls of normal and compression wood tracheids of Pinus radiata (radiata pine), Picea sitchensis (Sitka spruce) and Picea abies (Norway spruce) by transmission electron microscopy using immunogold labelling with monoclonal antibodies to (1-->4)-beta-galactan (LM5), (1-->3)-beta-glucan, arabinogalactan proteins (AGPs) (MAC207) and heteroxylans (LM10 and LM11). In fully differentiated compression wood tracheids, (1-->4)-beta-galactan was found in the S2((L)) layer and, to a smaller extent, at the interface between the compound middle lamella and the S1 layer. (1-->4)-beta-Galactan appeared to be displaced from, or modified in, the S1 layer during cell wall formation. (1-->3)-beta-Glucan (callose) was confined to the helical cavities in the inner S2 layer of severe compression wood. MAC207 AGP glycan epitope was found exclusively in the S1 and S3 layers of normal wood tracheids and in the S1 and inner S2 layers of compression wood tracheids. Binding of LM10, which specifically recognizes unsubstituted or low-substituted xylans, occurred at similar locations to the MAC207 epitope, whereas binding of LM11, which recognizes more highly substituted as well as unsubstituted xylans, occurred throughout the tracheid walls with the exception of the primary wall. Immunogold labelling showed that the different wall layers of softwood tracheids have different polysaccharide compositions which change abruptly during cell wall formation.

Download full-text PDF

Source
http://dx.doi.org/10.1093/treephys/tpq021DOI Listing

Publication Analysis

Top Keywords

compression wood
16
wood tracheids
16
arabinogalactan proteins
8
immunogold labelling
8
cell wall
8
wall formation
8
xylans occurred
8
wood
5
tracheids
5
distribution 1->4-beta-galactans
4

Similar Publications

3D porous carbon electrodes have attracted significant attention for advancing compressible supercapacitors (SCs) in flexible electronics. The micro- and nanoscale architecture critically influences the mechanical and electrochemical performance of these electrodes. However, achieving a balance between high compressive strength, electrochemical stability, and cost-effective sustainable production remains challenging.

View Article and Find Full Text PDF

The importance of continuous and reliable pulse wave monitoring is constantly being increased in health signal monitoring and disease diagnoses. Flexible pressure sensors with high sensitivity, low hysteresis and fast response time are an effective means for monitoring pulses. Herein, a special wave-shaped layered porous structure of carbonized wood cellulose sponge (CWCS) was constructed based on natural wood (NW).

View Article and Find Full Text PDF

Acoustic, Mechanical, and Thermal Characterization of Polyvinyl Acetate (PVA)-Based Wood Composites Reinforced with Beech and Oak Wood Fibers.

Polymers (Basel)

January 2025

Research Laboratory for Sustainable Development and Health, Department of Applied Physics, Faculty of Sciences and Technics, Cadi Ayyad University, Marrakesh 40000, Morocco.

Considering the growing need for developing ecological materials, this study investigates the acoustic, mechanical, and thermal properties of wood composites reinforced with beech or oak wood fibres. Scanning electron microscopy (SEM) revealed a complex network of interconnected pores within the composite materials, with varying pore sizes contributing to the material's overall properties. Acoustic characterization was conducted using a two-microphone impedance tube.

View Article and Find Full Text PDF

Recycling end-of-life wind turbines poses a significant challenge due to the increasing number of turbines going out of use. After many years of operation, turbines lose their functional properties, generating a substantial amount of composite waste that requires efficient and environmentally friendly processing methods. Wind turbine blades, in particular, are a problematic component in the recycling process due to their complex material composition.

View Article and Find Full Text PDF

Experimental Study on Mechanical Performance of Single-Side Bonded Carbon Fibre-Reinforced Plywood for Wood-Based Structures.

Materials (Basel)

January 2025

Department of Integrated Design and Tribology Systems, Faculty of Mechanics and Technology, Rzeszów University of Technology, ul. Kwiatkowskiego 4, 37-450 Stalowa Wola, Poland.

In addition to the traditional uses of plywood, such as furniture and construction, it is also widely used in areas that benefit from its special combination of strength and lightness, particularly as a construction material for the production of finishing elements of campervans and yachts. In light of the current need to reduce emissions of climate-damaging gases such as CO, the use of lightweight construction materials is very important. In recent years, hybrid structures made of carbon fibre-reinforced plastics (CFRPs) and metals have attracted much attention in many industries.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!