Purpose: The current study was carried out to evaluate the effect of doubling the adhesive layers of three acetone-based adhesives on the microtensile bond strength and ultra morphological characterization of the resin dentin interface using SEM.
Materials And Methods: A total of 27 caries-free human molars were used. Superficial flat dentin surfaces were obtained by wet grinding the buccal surfaces. Three adhesive systems Prime & Bond NT (G1), XENO IV (GII) and G BOND (GIII) were used according to three different protocols: (A) according to the manufacturer's instructions, (B) doubling the adhesive layers and light curing and (C): doubling the adhesive layers with intermediate curing between each layer. Resin composite buildups were made using TPH Spectrum resin composite on the bonded surfaces in 1 mm light cured increments for 40 seconds each. The bonded teeth were sectioned to obtain sticks for microtensile testing. The testing was conducted using a universal testing machine at a crosshead speed of 1 mm/minute. The microtensile bond strength means and standard deviations were calculated and the data were statistically analyzed using Two-way Analysis of Variance (ANOVA) and Tukey's post-hoc tests (p < or = 0.05). Ultra morphological characterization of the resin-dentin interface and representative fractured dentin specimens were examined using SEM.
Results: When applied according to the manufacturer's instructions, Prime & Bond NT (total etch adhesive) showed significantly high microtensile bond strength with a mean value +/- SD of 35 +/- 12.7 MPa followed by XENO IV (21.2 +/- 9.4 MPa), while G BOND presented a significantly lower mean value (10.9 +/- 2.9 MPa). Doubling the adhesive layers significantly reduced the mean strength of the total etch adhesive system; in contrast, it significantly increased the bond strength of both self-etch adhesives. The relatively thicker adhesive layer was seen with the total-etch adhesive when the application was doubled, while the hybrid layer appeared thicker with self-etch adhesives.
Conclusions: Doubling the adhesive layer applications significantly improved the bond strength of the two self-etch adhesives (XENO IV and G BOND); however, it had a negative effect on the bond strength of the total-etch adhesive (Prime & Bond NT).
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2341/08-089-L | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Weakening Pd─O Bonds by an Amorphous Pd Layer to Promote Electrocatalysis.
Small
January 2025
Institute of Materials for Energy and Environment, College of Materials Science and Engineering, Qingdao University, Qingdao, 266071, P. R. China.
Construction of core-shell structured electrocatalysts with a thin noble metal shell is an effective strategy for lowering the usage of the noble metal and improving electrocatalytic properties because of the structure-induced geometric and electronic effects. Here, the synthesis of a novel core-shell structured nanocatalyst consisting of a thin amorphous Pd shell and a crystalline PdCu core and its significantly improved electrocatalytic properties for both formic acid oxidation and oxygen reduction reactions are shown. The electrocatalyst exhibits 4.
View Article and Find Full Text PDFEffect of Chemical Treatment on the Mechanical and Hygroscopic Properties of an Innovative Clay-Sand Composite Reinforced with Fibers.
Materials (Basel)
January 2025
Laboratoire d'Energétique et des Transferts Thermique et Massique (LETTM), Faculté des Sciences de Tunis, Université de Tunis El Manar, Campus Universitaire El-Manar, El Manar, Tunis 2092, Tunisia.
The viability of using fibers as reinforcement material for developing lightweight sustainable non-structural construction materials in compliance with the valorization of local by-products has been investigated in this work. This study aims to investigate the effect of the chemical treatment of fibers on the mechanical and hygric properties of bio-sourced clay-sand- fiber composite. This lightweight specimen has been produced from a mixture of 60% natural clay and 40% sand by mass, as a matrix, and reinforced with different amounts of Juncus fibers.
View Article and Find Full Text PDFEffects of Moisture Infiltration on Interfacial Characteristics of Fiber Asphalt Mastic-Aggregate and the Cracking Resistance of Mixture.
Materials (Basel)
December 2024
College of Civil Science and Engineering, Yangzhou University, Yangzhou 225100, China.
Article Synopsis
- The study examines how moisture affects the bond between fiber asphalt mixtures and aggregate, impacting their cracking resistance.
- Researchers tested three types of fiber (basalt, glass, polyester) at various contents and used specific tests to measure interfacial strength.
- Results indicated that while fibers improve interfacial strength, moisture infiltration significantly weakens it, influencing the overall durability of asphalt pavement.
Dynamic Mechanical Properties and Energy Absorption Capabilities of Polyureas Through Experiments and Molecular Dynamic Simulation.
Polymers (Basel)
January 2025
State Key Laboratory of Chemical Safety, Qingdao 266000, China.
Polyurea (PUR) has been widely used as a protective coating in recent years. In order to complete the understanding of the relationship between PUR microstructure and its energy absorption capabilities, the mechanical and dynamic performance of PURs containing various macrodiol structural units were compared using material characterization techniques and molecular dynamic simulation. The results showed that the PUR polycarbonate diols formed as energy absorbing materials showed high tensile strength, high toughness, and excellent loss factor distribution based on the comparison of stress-strain tensile curves, glass transition temperatures, phase images, and dynamic storage loss modulus.
View Article and Find Full Text PDFSynergistic enhancement of hydrophobicity and mechanical properties of cellulose paper by (3-glycidoxypropyl) trimethoxy and rosin.
Int J Biol Macromol
January 2025
College of Biological Engineering, Sichuan University of Science and Engineering, Yibin, Sichuan 644005, China. Electronic address:
Cellulose-based paper is inherently poor in hydrophobicity and mechanical strength, limiting its practical applications in daily life such as packaging materials, water-resistant labels, and disposable tableware. This study aimed to develop an effective and eco-friendly strategy to address these limitations by enhancing the hydrophobicity and mechanical properties of cellulose paper. To achieve this, an internal sizing agent was prepared by combining (3-glycidoxypropyl) trimethoxy (GPS) with natural rosin.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!