Objective: The aim of this study was to examine the quality of root fillings in small and curved root canals using bidirectional radiographs and fluid transport (FT) measurements.
Study Design: Root canals in eighty 38 degrees -curved mesial roots of mandibular molars were prepared using a balanced force technique. Samples were divided into 4 groups of 20 each and obturated by either the cold lateral compaction (LC) or the single cone (SC) technique, using either epoxy resin-based or zinc oxide-eugenol sealers. Bidirectional (buccolingual and mesiodistal) radiographs were acquired from each root. The voids along the root filling were assessed. The FT along the root filling was measured using an FT monitoring device. The differences between the groups regarding FT and the bidirectional radiographic score were analyzed by means of a Kruskal-Wallis test. The correlation between the FT values and the radiographic scores were analyzed using a Spearman test.
Results: Three groups of LC or SC fillings containing epoxy resin-based sealers exhibited similar radiographic scores and FT values (P > .05). The group of SC fillings that contained zinc oxide-eugenol sealer had worse radiographic scores than the other groups (P = .047). The bidirectional radiographic scores and the FT values for the 80 filled roots were strongly correlated (r(2) = 0.519; P = .00001).
Conclusion: Root fillings of similar quality were confirmed in small and curved root canals filled using either a single cone or laterally compacted gutta-percha and epoxy resin-based sealers.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.tripleo.2009.07.046 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Evaluation of the efficiency of smear layer removal during endodontic treatment using scanning electron microscopy: an in vitro study.
BMC Oral Health
January 2025
Department of Dental Science, Damascus University, Damascus, Syria.
Background: The smear layer formed during root canal instrumentation negatively affects root canal irrigation activity, which in turn can affect the treatment prognosis of endodontic treatment.
Aim: The aim of this study is to compare the efficiency of smear layer and debris removal in root canals using different irrigation protocols using scanning electron microscopy (SEM).
Materials And Methods: The quality of smear layer removal throughout the root canal was assessed in 30 intact extracted teeth divided into 3 groups according to the irrigation protocol: Group 1: 3% sodium hypochlorite (NaOCL) alternately with 17% ethylenediaminetetraacetic acetate (EDTA) was used.
Prevalence and morphology of middle mesial canals in mandibular first molars and their relationship with anatomical aspects of the mesial root: a CBCT analysis.
BMC Oral Health
January 2025
Department of Endodontics, Shaanxi Provincial People's Hospital, Xi'an, China.
Background: This study aims to investigate the prevalence and morphology of middle mesial canal (MMC) in mandibular first molar (M1M) among a Northwestern Chinese population, and to analyze their relationship with anatomical aspects of the mesial root.
Methods: Cone beam computed tomography (CBCT) was utilized to evaluate 898 M1Ms and assess the incidence and morphology of MMC. The following parameters for M1M with or without MMC were obtained: the vertical distance between the first appearance of MMC and canal orifices (D), the distance between mesiobuccal (MB) and mesiolingual (ML) canals (D1), the buccolingual width(L1) and mesiodistal width (L2) of mesial roots, and the flatness degree(L1/L2) of mesial roots.
A novel artificial intelligence-powered tool for automated root canal segmentation in single-rooted teeth on cone-beam computed tomography.
Int Endod J
January 2025
OMFS IMPATH Research Group, Department of Imaging and Pathology, Faculty of Medicine, University of Leuven, Leuven, Belgium.
Aim: To develop and validate an artificial intelligence (AI)-powered tool based on convolutional neural network (CNN) for automatic segmentation of root canals in single-rooted teeth using cone-beam computed tomography (CBCT).
Methodology: A total of 69 CBCT scans were retrospectively recruited from a hospital database and acquired from two devices with varying protocols. These scans were randomly assigned to the training (n = 31, 88 teeth), validation (n = 8, 15 teeth) and testing (n = 30, 120 teeth) sets.
Comparing Sectional and Total Dentin Bond Strengths of Three Endodontic Sealers after Using the Single-cone Obturation Technique: An Study.
J Contemp Dent Pract
October 2024
College of Dentistry, Ajman University, Ajman P.O. Box 346, United Arab Emirates; Department of Endodontic, Faculty of Dentistry, Mansoura University, Egypt, Orcid: https://orcid.org/0000-0003-3391-5306.
Aim: This study aimed to investigate and compare the total and sectional bond strengths of three endodontic sealers when used with the single-cone obturation technique.
Materials And Methods: Forty-five human maxillary central incisors were prepared and divided into three groups according to the type of endodontic sealer: Group I (Gutta-percha/AH Plus Jet), group II (Gutta-percha/GuttaFlow 2), and group III (RealSeal/RealSeal SE). All canals were filled with the single-cone technique.
Presence and distribution of voids after using the single cone obturation technique with different sealer placement methods in canals with an isthmus.
J Dent Sci
January 2025
Department of Oral Emergency, Peking University School and Hospital of Stomatology & National Center for Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices& Beijing Key Laboratory of Digital Stomatology & NHC Key Laboratory of Digital Stomatology & NMPA Key Laboratory for Dental Materials, Beijing, China.
Background/purpose: The obturation of canals with irregular structures is still a challenge for single cone obturation technique (SC). The purpose of this study was to evaluate the presence and distribution of voids using SC with different sealer placement methods in the canal with a simulated band-shaped isthmus.
Materials And Methods: 3D-printed root canal models with band-shaped isthmuses were randomly divided into four groups according to different obturation methods.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!