Slot waveguides allow for high optical confinement in a planar optical waveguide. Here we show a method for maintaining this high degree of confinement in slot waveguides with sharp bends. This high confinement can be achieved by using an asymmetric slot-based structure, where the mode in the bend remains localized in the slot region. We show that the relative power inside the slot can be as high as 28% for a 1 mum radius bend in an air-clad silicon waveguide.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/oe.14.009197 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Tunable Filters Using Defected Ground Structures at Millimeter-Wave Frequencies.
Micromachines (Basel)
December 2024
Center of Excellence for Thin-Film Research and Surface Engineering (CETRASE), Department of Electrical and Computer Engineering, University of Dayton, Dayton, OH 45469, USA.
This paper explores the potential of phase change materials (PCM) for dynamically tuning the frequency response of a dumbbell u-slot defected ground structure (DGS)-based band stop filter. The DGSs are designed using co-planar waveguide (CPW) line structure on top of a barium strontium titanate (BaSrTiO) (BST) thin film. BST film is used as the high-dielectric material for the planar DGS.
View Article and Find Full Text PDFHigh-Performance CP Magneto-Electric Dipole Antenna Fed by Printed Ridge Gap Waveguide at Millimeter-Wave.
Sensors (Basel)
December 2024
Centre-Energie Materiaux et Telecommunications, Institut National de la Recherche Scientifique, Montreal, QC H5A 1K6, Canada.
This paper presents a high-performance circularly polarized (CP) magneto-electric (ME) dipole antenna optimized for wideband millimeter-wave (mm-wave) frequencies, specifically targeting advancements in 5G and 6G technologies. The CP antenna is excited through a transverse slot in a printed ridge gap waveguide (PRGW), which operates in a quasi-transverse electromagnetic (Q-TEM) mode. Fabricated on Rogers RT 3003 substrate, selected for its low-loss and cost-effective properties at high frequencies, the design significantly enhances both impedance and axial ratio (AR) bandwidths.
View Article and Find Full Text PDFA D-Band Dual-Polarized High-Gain LTCC-Based Reflectarray Antenna Using SIW Magnetoelectric-Dipole Elements.
Micromachines (Basel)
December 2024
State Key Laboratory of Millimeter-Waves, School of Information Science and Engineering, Southeast University, Nanjing 210096, China.
This paper presents a D-band dual linear-polarized wideband high-gain reflectarray (RA) antenna using low-temperature co-fired-ceramic (LTCC) technology. The proposed element comprises a dual-polarized magnetoelectric (ME) dipole and a multilayer slot-coupling substrate-integrated waveguide (SIW) phase-delay structure, which are organized in accordance with the receiving/reradiating (R/R) principle. The coverage of phase shifts for both orthogonal polarizations is set to be greater than 360 degrees by varying the length of the phase-delay structure.
View Article and Find Full Text PDFSuspended Slot Membrane Waveguide Based on Germanium-on-Silicon-on-Insulator at λ = 4.23 µm for CO Monitoring.
Micromachines (Basel)
November 2024
Institute of Microelectronics and Optoelectronics, Warsaw University of Technology, Koszykowa 75, 00-662 Warsaw, Poland.
In this work, we propose a novel suspended slot membrane waveguide (SSMW) utilizing a germanium-on-silicon-on-insulator (Ge-on-SOI) platform for carbon dioxide (CO) gas-sensing applications. The design and analysis focus on the absorption line of CO in the mid-infrared region, specifically at a wavelength of 4.23 µm.
View Article and Find Full Text PDFA high-gain gap waveguide-based 16 × 16 slot antenna array with low sidelobe level for mmwave applications.
Sci Rep
December 2024
Department of Electrical Engineering, Chalmers University of Technology, Gothenburg, Sweden.
This study presents the design of a high-gain 16 × 16-slot antenna array with a low sidelobe level (SLL) using a tapered ridge gap waveguide feeding network for Ka-band applications. The proposed antenna element includes four cavity-backed slot antennas. A tapered feeding network is designed and utilized for unequal feeding of the radiating elements.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!