Examination of dental casts in newborns with bilateral complete cleft lip and palate.

Int J Oral Maxillofac Surg

University Hospital of Cranio-Maxillofacial and Oral Surgery, Medical University of Vienna, Austria.

Published: October 2009

This study reports measurements of dental casts in patients up to 6 months of age with bilateral complete cleft lip and palate (BCLP). 25 mouth casts of newborns with BCLP were selected from the hospital archive. They were measured independently by two examiners who assigned numbers to each measurement, referring to the expected reproducibility. The investigators also classified each dental cast according to an established score. The absolute values of all measured distances (P-P', L-C1-C2-T, L'-C1'-C2'-T', P-L, P'-L', L-L', C1-C1', C2-C2', Q1-Q1', Q2-Q2', T-T', I-Q1Q1', I-Q2Q2', I-TT') are reported. Inter-observer reproducibility was acceptable with total measurement errors ranging from 0.5 to 1.4mm. Most reliability scores, ranging from 1 (very high) to 5 (very low), showed a mean between 2 and 3 (min 2.17; max 3.16). The two examiners rated only one patient differently, according to the applied classification scheme. The absolute measurement values of the two classification systems accorded with the literature. This is the first study to measure the distances according to an established protocol in BCLP patients. The measurements between certain landmarks are more precise than others; it may be possible to use the more precise points for a longitudinal study from birth to 18 years.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.ijom.2009.04.023DOI Listing

Publication Analysis

Top Keywords

dental casts
8
casts newborns
8
bilateral complete
8
complete cleft
8
cleft lip
8
lip palate
8
examination dental
4
newborns bilateral
4
palate study
4
study reports
4

Similar Publications

Background: While the majority of dentists and lab techs recommend dental-specific desktop printers, many of them use cheaper, more affordable 3D printers in their practice. The study aimed to compare the accuracy of two commercial non-dental stereolithography (SLA) 3D printers with a dental 3D printer for diagnostic dental casts.  Methods: A prototype stereolithographic (Standard Triangle/Tessellation Language (STL)) model of a dentoform was used as a master model to be printed by three 3D printers (n=10 for each printer).

View Article and Find Full Text PDF

This study aimed to investigate the release of metallic ions from cobalt-chromium (Co-Cr) alloys fabricated by additive manufacturing (AM) for comparison with dental casting. Co-Cr alloys were fabricated via AM using selective laser melting (SLM) and electron beam melting (EBM) in powder-bed fusion. Polished and mechanically ground specimens were prepared.

View Article and Find Full Text PDF

Evaluation of the Palatal Features in Relation to Graft Harvesting in the Saudi Population.

Medicina (Kaunas)

January 2025

Faculty in Pediatric Dentistry and Orthodontics, College of Dentistry, King Saud University, Riyadh P.O. Box 11545, Saudi Arabia.

The palate's morphological characteristics are of great importance, especially in periodontology, where the palatine tissue represents a source of tissue graft for multiple mucogingival surgeries. This study aimed to estimate the amount of donor tissue available through the average palatal height and average location of the greater palatine artery in the Saudi population according to age and gender. Digital casts for adult Saudi patients at the age of 18-60 years old with a mean age of 37.

View Article and Find Full Text PDF

Factors that affect alginates: a brief review.

Minerva Dent Oral Sci

January 2025

School of Dentistry, Department of Biomedical and Dental Sciences and Morphofunctional Imaging, University of Messina, Messina, Italy -

Alginates are widely used in dentistry for various applications due to their favorable properties, including ease of use, cost-effectiveness, and patient comfort. They are commonly employed for preliminary impressions of oral structures in dental practice. This study aims to assess the impact of different factors on the performance of alginate impression materials in dentistry.

View Article and Find Full Text PDF

The aims of this study were twofold: first, to investigate the surface roughness of different abutment materials prepared using various manufacturing methods; and, second, to evaluate colonization by Streptococcus mutans and Candida albicans according to abutment material and manufacturing method. Six material/manufacturing method combinations were investigated in this study, namely chromium-cobalt (Cr-Co) (prepared using casting, milling, and laser sintering) and titanium, zirconia, and anodized titanium (all prepared using milling); titanium (stock) abutments were used as the control group. Surface roughness of seven specimens from each group was evaluated using atomic force microscopy and scanning electron microscopy.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!