Purpose: The aim of this prospective case series study was to evaluate the short-term success rates of titanium screw-type implants with a chemically modified sand-blasted and acid-etched (mod SLA) surface after 3 weeks of healing.
Material And Methods: A total of 56 implants were inserted in the posterior mandible of 40 partially edentulous patients exhibiting bone densities of class I to III. After a healing period of 3 weeks, all implants were functionally loaded with a screw-retained crown or fixed dental prosthesis. The patients were recalled at weeks 4, 7, 12, and 26 for monitoring and assessment of clinical and radiological parameters, including implant stability quotient (ISQ) measurements.
Results: None of the implants failed to integrate. However, two implants were considered "spinners" at day 21 and left unloaded for an extended period. Therefore, 96.4% of the inserted implants were loaded according to the protocol tested. All 56 implants including the "spinners" showed favorable clinical and radiographic findings at the 6-month follow-up examination. The ISQ values increased steadily throughout the follow-up period. At the time of implant placement, the range of ISQ values exhibited a mean of 74.33, and by week 26, a mean value of 83.82 was recorded. Based on strict criteria, all 56 implants were considered successfully integrated, resulting in a 6-month survival and success rate of 100.0%.
Conclusion: This prospective study using an early-loading protocol after 3 weeks of healing demonstrated that titanium implants with the modified SLA surface can achieve and maintain successful tissue integration over a period of at least 6 months. The ISQ method seems feasible to monitor implant stability during the initial wound-healing period.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/j.1708-8208.2009.00148.x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Prognosis of Implant-Based Breast Reconstruction After Mastectomy Flap Necrosis: Predictors of Failure and Salvage.
Aesthetic Plast Surg
January 2025
Department of Plastic Surgery, Samsung Medical Center, Sungkyunkwan University School of Medicine, 81 Irwon-ro, Gangnam-gu, Seoul, 06351, Republic of Korea.
Background: In the realm of implant-based breast reconstruction, mastectomy flap necrosis (MFN) is a prevalent yet grave complication that poses a threat to the stability of the inserted prosthesis. Although numerous investigations have scrutinized the risk factors for MFN development, few have delved into the aftermath, specifically implant failure or salvage. This study seeks to appraise the prognosis of the implanted prosthesis following MFN occurrence, as well as identify predictors of such outcomes.
View Article and Find Full Text PDFAdditively Manufactured Subperiosteal Implants for the Rehabilitations of Lateral Incisors Agenesis - a case series.
J Stomatol Oral Maxillofac Surg
January 2025
Department of Prosthodontics and Gerostomatology, Poznan University of Medical Sciences, 60-792 Poznan, Poland.
Background: Tooth agenesis, particularly the absence of upper lateral incisors, presents substantial challenges for clinicians due to the associated bone atrophy, which limits the use of traditional implant solutions. Current options, such as endosseous implants combined with guided bone regeneration (GBR), often fail due to insufficient osseointegration in atrophic bone. This study aims to evaluate the effectiveness of custom-made, additively manufactured subperiosteal implants in addressing these challenges METHODS: This retrospective study assessed 16 custom-made subperiosteal implants used in 12 patients (10 females, 2 males; mean age 25 ± 2.
View Article and Find Full Text PDFOsseointegration for transfemoral amputees: Influence of femur length and implant sizing on bone-implant contact and alignment.
Injury
January 2025
Department of Orthopedic Surgery, McGovern Medical School, UTHealth Science Center at Houston, 5420 West Loop S. Suite 1300, Bellaire, TX, 77401, USA. Electronic address:
Introduction: Clinical data on osseointegration (OI) for limb replacement indicates a concerning increase in mechanical complications after five years post-implantation. Since adequate bone-implant contact and proper implant alignment are critical factors for successful osseointegration, it is essential to identify the factors influencing these outcomes. This study aimed to assess the effects of residual femur length and implant sizing on bone-implant contact and implant alignment.
View Article and Find Full Text PDFSynthesis, characterization and molecular docking of chitin-curcumin based thermoset polyurethane elastomers for angiogenic potential.
Int J Biol Macromol
January 2025
Department of Chemistry, The University of Lahore, Lahore, Pakistan.
This current study has been carried out to investigate the angiogenic potential and in silico studies of designed thermoplastic polyurethanes (PU) for biomedical potential. For this purpose, curcumin based thermoplastic polyurethanes has been synthesized by two step methodology. Different characterization techniques such as FTIR, solid state HNMR, CNMR and XRD were used to confirm the synthesis of designed thermoplastic polyurethanes.
View Article and Find Full Text PDFStructure Protects Function: A Multilevel Engineered Surface Modification Renders the Surface of Titanium Dental Implants Resistant to Bacterial Colonization.
ACS Appl Mater Interfaces
January 2025
DWI─Leibniz Institute for Interactive Materials e.V., Forckenbeckstraße 50, Aachen 52074, Germany.
The global dental implant market is projected to reach $9.5 billion by 2032, growing at a 6.5% compound annual growth rate due to the rising prevalence of dental diseases.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!