Bio-diesel oil has attracted much attention as a substitutable energy sources for its renewable and eco-friendly property. However, problems of lead contamination in fuel are also emphasized increasingly at present. So it was of quite significance to determine the contents of lead in bio-diesel oil and its raw material rapeseed oil. An effective method was developed for the rapid determination of lead in rapeseed oil and bio-diesel oil by graphite furnace atomic absorption spectrometry (GFAAS) after their stabilization as microemulsions. In this research work, polyethyleneglycol octyl phenyl ether and n-butanol were used for emulsifier and auxiliary emulsifying agent, respectively. For Pb, efficient thermal stabilization was obtained using NH4H2PO4 as matrix modifier. Sample stabilization was necessary because of evident analyte losses that occurred immediately after sampling. Excellent long-term sample stabilization and the influence of the microemulsion composition on the GFAAS response were observed by mixing different organic solvents. The ashing and atomization temperature and ramp rate influenced the sensitivity obtained for Ph. Take this into account, the optimum conditions of the graphite furnace atomic absorption spectrometric determination of Pb in rapeseed oil and bio-diesel oil samples were investigated. The results showed that the microemulsion was quite stable when the value of V(20% polyethyleneglycol octyl phenyl ether), V(n-butanol), V(oil) and V(water) was 0.1: 8.9: 0.5: 0.5, without matrix interference effect. The determination limit of the proposed method was 126.2 microg x L(-1) for Pb, comfortably below the values found in the analyzed samples. The recoveries were from 81.8% to 109.0%, which performed using the addition of different concentrations of lead to bio-diesel oil, rapeseed oil and petrochemical diesel samples. The relative standard deviation of determination was 5.84%. This work showed the great efficiency of the microemulsion, indicating that it is possible to extract lead from the oil phase. The method was applied to the determination of lead in oil samples with satisfactory results.

Download full-text PDF

Source

Publication Analysis

Top Keywords

bio-diesel oil
24
rapeseed oil
20
oil
13
oil bio-diesel
12
lead bio-diesel
8
determination lead
8
graphite furnace
8
furnace atomic
8
atomic absorption
8
polyethyleneglycol octyl
8

Similar Publications

Characterisation and anaerobic digestion of fat, oil and grease (FOG) waste from wastewater treatment plants.

J Environ Manage

January 2025

Department of Civil, Environmental and Architectural Engineering, University of Padova, Via Marzolo 9, 35131, Padova, Italy.

The materials removed in the oil separation units of wastewater treatment plants can be referred to as fat, oil and grease (FOG) waste. FOG waste accumulation in treatment plants can cause clogging of pipes, production of excessive scums and foams, and negatively affect air/liquid oxygen transfer. While conventional disposal routes of this material can be limited by its water and organic content, FOG can represent a source of bio-energy other than bio-diesel production.

View Article and Find Full Text PDF

The equilibrium swelling test was employed to determine the swelling response of Nitrile Butadiene Rubber (NBR) with various acrylonitrile (ACN) contents, and the three-dimensional solubility parameter (HSP) and modified Flory-Huggins interaction parameter (χ) were used to establish the prediction model of the oil-resistant property. The results indicate that the energy difference (Ra) between NBR and solvents calculated by HSP values can be correlated with the swelling response qualitatively with an inversed "S-shape", and high swelling response occurs at Ra < 8 MPa for NBR. For the purpose of establishing the prediction model, the new modified χ value has been calculated and fitted with the swelling response using exponential and logarithmic fittings, respectively.

View Article and Find Full Text PDF

Bio-diesel is used for engine as a replacement of diesel fuel which is characterized by lower emission, low pollution and renewable some of fuel. This study focus on how to enhance the production of bio-oil from Jatropha seeds by using microwave and ultrasonic as pre-treatments. To achieve that, the effects of extraction temperature (60, 80, 100 and 120 °C) and extraction screw speed (60, 90 and 120 rpm) on oil extraction yield and quality, extraction energy requirements and extraction time and were studied.

View Article and Find Full Text PDF

Dealing with the current defaults of environmental toxicity, heating, waste management, and economic crises, exploration of novel non-edible, toxic, and waste feedstock for renewable biodiesel synthesis is the need of the hour. The present study is concerned with Buxus papillosa with seeds oil concentration (45% w/w), a promising biodiesel feedstock encountering environmental defaults and waste management; in addition, this research performed simulation based-response surface methodology (RSM) for Buxus papillosa bio-diesel. Synthesis and application of novel Phyto-nanocatalyst bimetallic oxide with Buxus papillosa fruit capsule aqueous extract was advantageous during transesterification.

View Article and Find Full Text PDF

Karanja oil blended with diesel acts as a good alternative for a CI engine due to its low emission and high oxygen content as compared to pure diesel which leads to the non-toxic and biodegradable nature of the fuel. The objective of this project is to enhance the performance and emission characteristics of a diesel engine that runs on biofuel by accurately calibrating its fuel injector control parameters. To achieve this goal, the project focuses on creating optimal split injector control maps using a novel global model-based calibration approach that considers the entire range of engine speed-load conditions.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!