Transport properties of pure methane gas have been calculated in the rigid-rotor approximation using the recently proposed intermolecular potential energy hypersurface [R. Hellmann et al., J. Chem. Phys. 128, 214303 (2008)] and the classical-trajectory method. Results are reported in the dilute-gas limit for shear viscosity, viscomagnetic coefficients, and self-diffusion in the temperature range of 80-1500 K. Compared with the best measurements, the calculated viscosity values are about 0.5% too high at room temperature, although the temperature dependence of the calculated values is in very good agreement with experiment between 210 and 390 K. For the shear viscosity, the calculations indicate that the corrections in the second-order approximation and those due to the angular-momentum polarization are small, less than 0.7%, in the temperature range considered. The very good agreement of the calculated values with the experimental viscosity data suggests that the rigid-rotor approximation should be very reasonable for the three properties considered. In general, the agreement for the other measured properties is within the experimental error.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1063/1.2958279 | DOI Listing |
Biotechnol Prog
March 2025
Department of Biochemistry and Molecular & Cellular Biology, Georgetown University, Washington, DC, USA.
The organ transplantation field requires new approaches for replacing and regenerating tissues due to the lack of adequate transplant methods. Three-dimensional (3D) extrusion-based bioprinting is a rapid prototyping approach that can engineer 3D scaffolds for tissue regeneration applications. In this process, 3D printed cell-based constructs, consisting of biomaterials, growth factors, and cells, are formed by the extrusion of bioinks from nozzles.
View Article and Find Full Text PDFWater Res
February 2025
Guangdong-Hong Kong Joint Laboratory for Water Security, Beijing Normal University, Zhuhai 519087, China; Department of Civil and Environmental Engineering, National University of Singapore, 1 Engineering Drive 2, 117576, Singapore. Electronic address:
Aerobic granular sludge (AGS) has demonstrated a lower fouling propensity than floc sludge in membrane bioreactors (MBRs) due to various hypotheses, including differences in particle size and the efficacy of physical scouring. However, controversy exists regarding the dominant cause of this lower fouling. Therefore, in this work, we systematically investigated the contribution of four potential mechanisms of AGS on membrane fouling alleviation in MBRs: 1) loosening cake layer; 2) scouring of the membrane surface; 3) regulating soluble microbial product (SMP) secretion; and 4) changing the rheology of the bulk solution.
View Article and Find Full Text PDFACS Biomater Sci Eng
March 2025
Department of Materials Science and Engineering, University of Michigan, Ann Arbor, Michigan 48109, United States.
Creating customizable soft medical implants and devices tailored to patient-specific anatomy represents a significant challenge in healthcare, requiring 3D-printable materials with viscoelastic properties similar to those of natural tissue, high adaptability, and biocompatibility. Here, we develop a family of silicone organogel inks for 3D printing of tunable soft biomaterials via direct ink writing (DIW). We have developed a set of ink formulations comprising photo-cross-linkable silicone polymers, silicone oil, and fumed silica nanoparticles to modify the rheological behavior of the inks, optimize their printability, and control the viscoelastic properties of the printed organogel materials.
View Article and Find Full Text PDFFood Res Int
April 2025
Gembloux Agro-Bio Tech TERRA University of Liège Avenue de la Faculté d'Agronomie 2B, Gembloux 5030, Belgium.
Laminated pastries rely heavily on the unique viscoelastic and plastic properties of margarine. Traditional methods for predicting such properties, such as solid fat content (SFC), hardness, small amplitude oscillatory rheology, and subjective sensory tests (thumb test), often lack the sensitivity to detect subtle variations in margarine possessing similar characteristics. SFC primarily focuses on solid fat content, hardness measurement with cone provides a single-point assessment and identifying linear viscoelastic region cannot adequately describe the non-linear behavior which is crucial for lamination processes involving significant deformations.
View Article and Find Full Text PDFNutrition
February 2025
Faculty of Medicine, Acıbadem University, Istanbul, Turkey.
Objectives: Our study is centered around a pivotal question: How does the increase in adipose tissue, which defines obesity, impact hemorheological parameters? By delving into this question, we aim to underscore the crucial role of fat tissue increase in obesity, a topic of significant interest and importance in the field of physiology and obesity research.
Methods: Individuals with a body mass index (BMI) of 25 and above were included in this study. Height was measured with bare feet on flat surface, then, using the bioimpedance device (Tanita-BC418), weight, BMI, fat percentage, fat mass (FM), and fat-free mass were determined.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!