The compression of direct-drive, spherical implosions is studied using cryogenic D2 targets on the 60-beam, 351-nm OMEGA laser with intensities ranging from approximately 3x10(14) to approximately 1x10(15) W/cm2. The hard-x-ray signal from hot electrons generated by laser-plasma instabilities increases with laser intensity, while the areal density decreases. Mitigating hot-electron production, by reducing the laser intensity to approximately 3x10(14) W/cm2, results in areal density of the order of approximately 140 mg/cm2, in good agreement with 1D simulations. These results will be considered in future direct-drive-ignition designs.

Download full-text PDF

Source
http://dx.doi.org/10.1103/PhysRevLett.100.185005DOI Listing

Publication Analysis

Top Keywords

compression direct-drive
8
laser intensity
8
areal density
8
role hot-electron
4
hot-electron preheating
4
preheating compression
4
direct-drive imploding
4
imploding targets
4
targets cryogenic
4
cryogenic ablators
4

Similar Publications

In order to improve the stability of the pulse, realize the high requirements of the direct drive ignition design for the uniformity of the target irradiation, reduce the interference of laser plasma instability, and improve the laser-target coupling efficiency, a nanosecond laser spatial-temporal modulation of high-power laser driver for double-cone ignition (DCI) research was proposed. Under the premise of satisfying the near-isentropic compression waveform of driving implosion, the time-power curves of all sub-beams in the facility are redistributed to reduce the waveform contrast ratio of each sub-beam. A fewer number of sub-beams are utilized to generate low-power foot pulses, which are focused on the target surface of the initial radius.

View Article and Find Full Text PDF

Precise modeling of shocks in inertial confinement fusion implosions is critical for obtaining the desired compression in experiments. Shock velocities and postshock conditions are determined by laser-energy deposition, heat conduction, and equations of state. This paper describes experiments at the National Ignition Facility (NIF) [E.

View Article and Find Full Text PDF

Laser-direct-drive fusion target design with a high-Z gradient-density pusher shell.

Phys Rev E

September 2023

Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623-1299, USA.

Laser-direct-drive fusion target designs with solid deuterium-tritium (DT) fuel, a high-Z gradient-density pusher shell (GDPS), and a Au-coated foam layer have been investigated through both 1D and 2D radiation-hydrodynamic simulations. Compared with conventional low-Z ablators and DT-push-on-DT targets, these GDPS targets possess certain advantages of being instability-resistant implosions that can be high adiabat (α≥8) and low hot-spot and pusher-shell convergence (CR_{hs}≈22 and CR_{PS}≈17), and have a low implosion velocity (v_{imp}<3×10^{7}cm/s). Using symmetric drive with laser energies of 1.

View Article and Find Full Text PDF
Article Synopsis
  • - The study discusses the use of a hybrid-drive (HD) scheme to improve pressure boosting and smoothing challenges in laser-driven inertial confinement fusion, leading to more stable implosion and ignition.
  • - Experiments conducted with hemispherical and planar ablator targets in a scaled-down semicylindrical hohlraum achieved a peak radiation temperature of approximately 200 eV using indirect-drive laser energies of 43-50 kJ.
  • - The results show that direct-drive laser energies of 3.6-4.0 kJ can create significantly boosted HD pressures, with additional findings indicating effective pressure smoothing and the suppression of asymmetric shocks by a strong symmetric HD shock.
View Article and Find Full Text PDF

A wide-range (0 to 1044.0 g/cm^{3} and 0 to 10^{9} K) equation-of-state (EOS) table for a CH_{1.72}O_{0.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!