Changes in chromium distribution during the electrodialytic remediation of a Cr (VI)-contaminated soil.

Environ Geochem Health

Instituto Geológico y Minero de España, Dept. Investigación y Prospectiva Geocientifica, C/Rios Rosas, 23, 28003 Madrid, Spain.

Published: April 2008

A laboratory study has been carried out to determine the feasibility of in situ remediation of chromium (VI)-contaminated soil using electrodialysis in relation to its speciation in soil. This technique is best suited for low-permeability soils or sediments, which may be difficult to remediate by other means and implies the application of a low-intensity direct current to the soil, which is separated from the electrode compartments by ion-exchange membranes. A clayey soil was prepared for use in the experiments and was characterized before being mixed with a solution of potassium dichromate for several days to produce a final Cr content of 4,056 mg/kg of soil dry wt. Remediation tests were carried out under constant-voltage conditions for periods of 7-14 days and the evolution of applied current to the cell, pH, and conductivity of the electrolytes were recorded periodically. Fractionation of chromium was determined for soil samples before and after remediation using a standardized four-step sequential extraction procedure (SEP) with acetic acid, hydroxylamine, hydrogen peroxide, and aqua regia solutions. Results show that chromium is mobilized from the most labile phases (soluble/exchangeable/carbonate). In a 15 V test, SEP results show that the amount of chromium extracted in the first step drops from 80% to 9%, but also that changes in the total chromium distribution occur during the treatment with some transferred to other soil phases that are more difficult to mobilize.

Download full-text PDF

Source
http://dx.doi.org/10.1007/s10653-008-9137-1DOI Listing

Publication Analysis

Top Keywords

chromium distribution
8
soil
8
vi-contaminated soil
8
chromium
5
changes chromium
4
distribution electrodialytic
4
remediation
4
electrodialytic remediation
4
remediation vi-contaminated
4
soil laboratory
4

Similar Publications

This study aimed to investigate the release of metallic ions from cobalt-chromium (Co-Cr) alloys fabricated by additive manufacturing (AM) for comparison with dental casting. Co-Cr alloys were fabricated via AM using selective laser melting (SLM) and electron beam melting (EBM) in powder-bed fusion. Polished and mechanically ground specimens were prepared.

View Article and Find Full Text PDF

This study investigated the elemental composition of , addressing the gap in comprehensive trace element profiling of this medicinal plant. The research aimed to determine the distribution of macronutrients, micronutrients, and beneficial and potentially toxic elements across different plant parts (seeds, leaves, stems, and roots). Using ICP-OES analysis, two digestion methods were employed to capture both complex and labile elements.

View Article and Find Full Text PDF

Nanoscale Fe(0)-zeolite composite derived from coal bottom ash for efficient treatment of Cr(VI)-contaminated groundwater: Unveiling the importance of locations for surface-bound Fe(II) and Fe(0) passivation products.

J Hazard Mater

January 2025

Department of Civil and Environmental Engineering, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029, Republic of Korea; Department of Environmental Engineering, Graduate School, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029, Republic of Korea. Electronic address:

The synthesis of coal bottom ash-induced zeolite (Si-Al material) has been widely reported; however, the selective recovery of the three main elements, viz., Si, Al, and Fe, from coal bottom ash for the synthesis of reactive adsorbents has not yet been reported. In this study, we separated the magnetic and non-magnetic fractions of coal bottom ash to selectively recover Fe and Si-Al for synthesizing nanoscale zero-valent iron@zeolite (NZVI@ZBA) composites with uniform formation of Fe(0) nanoparticles on the ZBA surface.

View Article and Find Full Text PDF

Background Dentures are one of the main treatments dentists deliver to restore the oral function and aesthetics of individuals with missing teeth. Clinical denture fabrication and manufacturing is one of the main training modules for undergraduates during dental clinical training. However, students often face problems during denture delivery due to multiple factors causing discomfort to patients, affecting the quality of the denture and the patient's adaptation period to the denture.

View Article and Find Full Text PDF

Background: Zygomatic implants are becoming an ideal treatment approach for implant-supported prosthesis treatment developed for the atrophic maxilla. This study aims to evaluate the amount and distribution of stress in implants and peri-implant bone using different implant-supported prosthesis configurations in Aramany Class I maxillary defects through 3-dimensional finite element analysis.

Methods: A 3-dimensional finite element model of the Aramany class I defect was created.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!