The purpose of this study was to measure the impact of external shear force and pressure on a superficial layer of skin and subcutaneous layer with an underlying bony prominence, and also to verify how the influence of these external forces can be reduced after dressings are applied. For this purpose, an experimental model was prepared, consisting of porcine skin and a Predia sensor capable of measuring pressure and shear force simultaneously. External force was applied to the skin model using a 1 kg weight consisting of metal beads. As a result, the control of the shear force value in the subcutaneous layer became approximately 35% smaller than the control in the superficial layer. The shear forces present in the subcutaneous layer were significantly reduced to within 31-45% when compared with the control values, depending on the dressing applied. Regarding the maximum pressures in the subcutaneous layer, the pressure measured following movement was 2.4 times higher in the control than the static pressure and they were also 1.3-1.8 times higher than the static pressure in all instances with the dressing tested. All the dressing materials tested proved to be effective in reducing pressure in the subcutaneous layer compared with the control. Film dressings and hydrocolloid dressings were more effective than hydropolymer and hydrocellular dressings. From the above results, we conclude that efforts made to reduce shear force and pressure may be clinically important.

Download full-text PDF

Source
http://dx.doi.org/10.1111/j.1524-475X.2007.00325.xDOI Listing

Publication Analysis

Top Keywords

shear force
24
subcutaneous layer
20
pressure shear
12
superficial layer
12
dressing materials
12
pressure
9
influence external
8
external forces
8
layer
8
porcine skin
8

Similar Publications

Numerical simulation study on the influence of bend diameter rate on the flow characteristics of nature gas hydrate particles.

Sci Rep

December 2024

Jiangsu Key Laboratory of Oil-Gas Storage and Transportation Technology, Changzhou University, Changzhou, 213164, Jiangsu, China.

Bend pipe is a common part of long distance pipeline. There is very important to study the flow law of hydrate particles in the bend pipe, and pipeline design will be optimized. In addition, the efficiency and safety of pipeline gas transmission will be improved.

View Article and Find Full Text PDF

In a slim-floor structural system, beams and slabs are placed at the same level, reducing the overall floor height and material usage in vertical structures, thereby improving economic efficiency. The use of slim-floor structures is common practice in Finnish construction where these structures are typically constructed using hollow-concrete slabs and welded steel box beams. However, in Finland, only a few buildings utilise cross-laminated timber (CLT) slabs in slim-floor structures, and none have incorporated the composite action between CLT and steel beams.

View Article and Find Full Text PDF

This study aimed to evaluate the effects of salt addition and different thermal-assisted pressure processing (TAPP) conditions (temperature and pressure levels) on technological, chromatic, and textural parameters and lipid oxidation of Superficial pectoralis beef muscle. A factorial design with three factors was applied: KCl/NaCl marination (marinated samples MS; non-marinated samples, NMS), temperature during high-pressure processing (50, 70°C), and pressure level (0.1, 200, and 300 MPa).

View Article and Find Full Text PDF
Article Synopsis
  • GPE extract from traditional Chinese medicine shows promise in enhancing growth performance and meat quality in ducks.
  • The study involved 480 ducks receiving different levels of GPE over 7 weeks, with the highest dosage (600 mg/kg) leading to significant health benefits.
  • Findings indicated improvements in serum antioxidant capacity, immune function, and meat characteristics like moisture content and tenderness, suggesting GPE could be a viable alternative to antibiotics in poultry farming.
View Article and Find Full Text PDF

Fused Filament Fabrication (FFF) printing is one of the most all-purpose manufacturing techniques, allowing many complicated parts to be obtained at lower cost. This is especially important in prosthetics, where more complex prostheses, especially of a hand, can cause enormous expense. However, providing the full functionality of a prosthesis often requires combining materials with different properties, such as rigidity and flexibility.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!