This paper assesses the potential of multivariate statistical analysis (MSA) applied to electron backscattered diffraction (EBSD) data. Instead of directly indexing EBSD patterns on an individual basis, this multivariate approach reduces a large (thousands) set of individual EBSD patterns into a core set of statistically derived component EBSD patterns which can be subsequently indexed. The following hypotheses are considered in this paper: (1) experimental EBSD patterns from a microstructure can be analytically treated as linear combinations of spatially simple components, (2) MSA has an angular resolution on par with standard EBSD, (3) MSA can discriminate between similar and dissimilar phases, and (4) the MSA approach can improve the effective spatial resolution of automated EBSD.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.ultramic.2007.10.013 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
In Situ EBSD Observation and Numerical Simulation of Microstructure Evolution and Strain Localization of DP780 Dual-Phase Steel.
Materials (Basel)
January 2025
School of Materials Science and Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, China.
To reveal the microstructural evolution and stress-strain distribution of 780 MPa-grade ferrite/martensite dual-phase steel during a uniaxial tensile deformation process, the plastic deformation behavior under uniaxial tension was studied using in situ EBSD and crystal plastic finite element method (CPFEM). The results showed that the geometrically necessary dislocations (GND) in ferrite accumulated continuously, which is conducive to the formation of grain boundaries, but the texture distribution did not change significantly. The average misorientation angle decreased and the proportion of low-angle grain boundaries increased with the increase of strain.
View Article and Find Full Text PDFMicrostructure and Thermal Cyclic Behavior of FeNiCoAlTaB High-Entropy Alloy.
Materials (Basel)
January 2025
Department of Materials Science and Engineering, National Taiwan University, Taipei 10617, Taiwan.
This study investigates the grain morphology, microstructure, magnetic properties and shape memory properties of an FeNiCoAlTaB (at%) high-entropy alloy (HEA) cold-rolled to 98%. The EBSD results show that the texture intensities of the samples annealed at 1300 °C for 0.5 or 1 h are 2.
View Article and Find Full Text PDFCrystal and Dislocation Characteristics of Ti-6Al-4V Alloy Under Effect of Laser Shock Peening.
Materials (Basel)
January 2025
College of Materials Science and Engineering, Chongqing University, Chongqing 400045, China.
Laser shock peening (LSP) is an effective method for enhancing the fatigue life and mechanical properties of Ti alloys. However, there is limited research on the effects of LSP on crystal structure and dislocation characteristics. In this study, Ti-6Al-4V alloy was subjected to laser shock peening with varying laser power levels.
View Article and Find Full Text PDFEffect of Tool Shoulder Profile on Grain and Texture Development in the Weld Interface Zone of Friction-Stir-Welded Dissimilar AA2024/AA7075 Joints.
Materials (Basel)
January 2025
College of Intelligent Manufacturing, Huanghuai University, Zhumadian 463000, China.
Friction-stir-welded dissimilar AA2024/AA7075 joints have an apparent influence on grain and texture development at the weld interface due to differences in physical and chemical properties between the two aluminum alloys. In this work, the effect of tool shoulder profile on grain structure and texture evolution in the center interface zone (CIZ) and bottom interface zone (BIZ) of dissimilar AA2024/AA7075 joints were quantitatively studied by electron back-scattering diffraction (EBSD). The results indicate that abundant fine and coarse equiaxial grains are produced in the CIZ and BIZ of the joints produced with a concentric circle shoulder (CCS) and three-helix shoulder (THS), and the average grain size of the BIZ is lower than that of the CIZ for the same CCS or THS joint.
View Article and Find Full Text PDFStrain-Controlled Thermal-Mechanical Fatigue Behavior and Microstructural Evolution Mechanism of the Novel Cr-Mo-V Hot-Work Die Steel.
Materials (Basel)
January 2025
School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471023, China.
In response to the intensifying competition in the mold market and the increasingly stringent specifications of die forgings, the existing 55NiCrMoV7 (MES 1 steel) material can no longer meet the elevated demands of customers. Consequently, this study systematically optimizes the alloy composition of MES 1 steel by precisely adjusting the molybdenum (Mo) and vanadium (V) contents. The primary objective is to significantly enhance the microstructure and thermal-mechanical fatigue performance of the steel, thereby developing a high-performance, long-life hot working die steel designated as MES 2 steel.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!