Statement Of Problem: Dynamic mechanical properties of hard, direct reline resins are important factors in the clinical success of dentures. However, little information is available on the nature of these properties.
Purpose: This study evaluated the dynamic mechanical properties of a variety of hard, direct reline resins: (1) visible light-polymerized, powder-liquid type, (2) visible light-polymerized, paste-type, (3) autopolymerized, powder-liquid type, as classified by component composition and mode of polymerization activation, namely, type of delivery system, and (4) heat-polymerized denture base materials.
Material And Methods: The dynamic mechanical analysis (DMA) of 8 commercial hard denture reline materials (HDR) (2 visible light-polymerized, powder-liquid type, 4 visible light-polymerized, paste-type, and 2 autopolymerized, powder-liquid type), and 2 heat-polymerized denture base materials was obtained at a frequency of 1 Hz at 37 degrees C. Five specimens of each material, 40.0 x 7.0 x 2.0 mm, were made to measure the elastic (storage) (E') and inelastic (loss) (E'') moduli, and loss tangent (tan delta). These parameters were compared with MANOVA and Student-Newman-Keuls test (alpha =.05).
Results: The E' values of 3 visible light-polymerized, paste-type reline resins were significantly higher than those of the other 5 reline resins. However, the E' values of all reline resins were significantly lower than those of the 2 heat-polymerized denture base resins. Except for 1 autopolymerized reliner, all reline materials had significantly lower E'' than the heat-polymerized denture base resins. The tan delta values of all but 1 visible light- and autopolymerized reliners were significantly higher than those of the heat-polymerized denture base materials.
Conclusions: Three visible light-polymerized, paste-type reline resins showed greater stiffness than the visible light- or autopolymerized, powder-liquid type reline resins. However, all of the hard, direct reline resins, including the 3 paste-type materials, exhibited greater flexibility compared to the heat-polymerized denture base resins.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/S0022-3913(07)60105-X | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Assessing shear bond strength of various surface treatments of 3D-printed provisional material with bis-acryl relining material.
BMC Oral Health
December 2024
Division of Prosthodontics, Faculty of Dentistry, Thammasat University, Pathum Thani, 12120, Thailand.
Objective: Marginal adaptation of the provisional restoration often requires relining from relining materials. This study determined the effects of surface treatments on the shear bond strength (SBS) between 3D-printed provisional and bis-acryl relining materials.
Materials And Methods: The 3D-printed provisional specimens (9 × 9 × 2 mm) were prepared using methacrylate-based material.
Tensile bond strength of soft relining materials to CAD-CAM denture base materials.
J Prosthodont
December 2024
Division of Comprehensive Oral Health, Department of Restorative Sciences, School of Dentistry, Birmingham, Alabama, USA.
Purpose: This study aimed to investigate the tensile bond strength between soft relining materials and different denture base materials.
Materials And Methods: The study was conducted in accordance with ISO 23401:2023. A total of 288 rectangular specimens (10L × 10H × 20W mm) were fabricated from various denture base materials, including a heat-compression polymethylmethacrylate (PMMA), two types of milled PMAA, and three types of 3D-printed resins, with bonding using two chairside soft reline materials (Coe-Soft and Lynal).
Effect of mechanical and chemical surface treatments on the repairing of milled and 3D-printed denture bases.
Sci Rep
October 2024
Department of Prosthodontics, Faculty of Dentistry, Chulalongkorn University, 34 Henri-Dunant Road, Pathumwan, Bangkok, 10330, Thailand.
Ensuring a strong bond between chairside autopolymerized acrylic resin to denture base is essential for denture repair and reline procedures. However, there is no established protocol to enhance bond strength between autopolymerizing resin and computer-aided design and computer-aided manufacturing (CAD-CAM) denture base materials. The purpose of this study was to determine shear bond strength of CAD-CAM denture bases and autopolymerizing acrylic resin after mechanical and chemical surface treatments compared with heat-polymerized acrylic resin.
View Article and Find Full Text PDFBond Strength of Nanocomposite Hard Liner to CAD-CAM Milled, 3D Printed, and Conventionally Fabricated Denture Base Resins.
Dent J (Basel)
August 2024
Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, P.O. Box 1982, Dammam 31441, Saudi Arabia.
Background: To investigate the effect of zirconium dioxide nanoparticles (ZrONPs) on the shear bond strength (SBS) of hard denture lines bonded to different denture base resins.
Methods: Five different denture bases were used in this study: conventional heat-cured resin, IvoCad, AvaDent, NextDent, and FormLabs, in acrylic specimens of 10 × 10 × 2.5 mm (N = 150, n = 10).
Effect of thermocycling on tensile bond strength of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 4 different denture liners: an in vitro study.
BMC Oral Health
August 2024
Department of Prosthodontics, Faculty of Dentistry, Chulalongkorn University, 34 Henri-Dunant Road, Pathumwan, Bangkok, 10300, Thailand.
Background: Digitally fabricated dentures may require relining due to continual alveolar ridge resorption. However, studies evaluating the tensile bond strength (TBS) of digitally fabricated dentures bonded to denture liners are lacking. This study aimed to evaluate the TBS of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 2 acrylic-based and 2 silicone-based denture liners, both before and after thermocycling.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!