Counteranion effects on propylene polymerization rates and stereoselectivities are compared using Cs-symmetric Me2C(Cp)(Flu)ZrMe2 (1; Cp = C5H4,eta5-cyclopentadienyl; Flu = C13H8, eta5-fluorenyl) and C1-symmetric Me2Si(OHF)(CpR*)ZrMe2 (2; OHF = C13H16, eta5-octahydrofluorenyl; CpR* = eta5-3-(-)-menthylcyclopentadienyl) precatalysts activated with the mononuclear and polynuclear perfluoroarylborate, -aluminate, and -gallate cocatalysts/activators B(C6F5)3 (3), B(o-C6F5C6F4)3 (4), Al(C6F5)3 (5), Ph3C+B(C6F5)4- (6) Ph3C+FAl(o-C6F5C6F4)3- (7), Ga(C6F5)3 (8), and recently reported mono- and polymetallic trityl perfluoroarylhalometalates Ph3C+FB(C6F5)3- (9), Ph3C+FB(o-C6F5C6F4)3- (10), (Ph3C+)xFx[Al(C6F5)3]yx- (x = 1, y = 1, 11; x = 1, y = 2, 12; x = 2, y = 3, 13), Ph3C+(C6F5)3AlFAl(o-C6F5C6F4)3- (14), Ph3C+XAl(C6F5)3- (X = Cl, 15; X = Br, 16), and Ph3C+F[Ga(C6F5)3]2- (17). Temperature, propylene concentration, and solvent polarity dependence are surveyed in polymerizations catalyzed by 1 activated with cocatalysts 3-16 and with a 1:2 ratio of Ph3CCl and 5, and with a 1:2 ratio of Ph3CBr and 5, and by 2 activated with 3, 6, 7, 12, and 14. Remarkable stereocontrol with high activities is observed for 1 + 12 and 1 + 14. Polypropylene samples produced using C1-symmetric precatalyst 2 are subjected to microstructural analyses using stochastic models describing the relative contributions of enantiofacial misinsertion and backskip processes. A powerful technique is introduced for calculating interparametric correlation matrices for these nonlinear stochastic models. The collected results significantly extend what is known about ion-pairing effects in the case of Cs-symmetric precatalyst 1 and allow these findings to be applied to the case of C1-symmetric precatalyst 2 as an agent of isospecific propylene polymerization.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/ja0680360 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Fabrication of Quasi-Solid Polymer Electrolytes for Lithium Metal Battery via Photopolymerization-Induced Microphase Separation.
ACS Appl Mater Interfaces
January 2025
Universite de Pau et des Pays de l'Adour, E2S UPPA, CNRS, IPREM, 64053, Pau, France.
The photopolymerization-induced microphase separation (photo-PIMS) process involving a reactive polymer block was implemented to fabricate nanostructured quasi-solid polymer electrolytes (QSPEs) for use in lithium metal batteries (LMBs). This innovative one-pot fabrication enhances interfacial properties in LMBs by enabling nanostructuring of QSPE directly onto the electrodes. This process also allows for customization of QSPE structural dimensions by tweaking the architecture and molar mass of poly[(oligo ethylene glycol) methyl ether methacrylate--styrene] (P(OEGMA--S)) macromolecular chain transfer agent.
View Article and Find Full Text PDFSynergistic effects of reduced graphene oxide on the antibacterial activity of calcium hydroxide-based intracanal medicaments containing different vehicles.
J Oral Sci
January 2025
Department of Conservative Dentistry, School of Dentistry and Institute of Oral Bioscience, Jeonbuk National University.
Purpose: This study investigated the synergistic effects of reduced graphene oxide (RGO) on the antibacterial activity of three calcium hydroxide-based intracanal medicaments with different vehicles.
Methods: Multispecies biofilms were cultured in a bovine root canal model. Intracanal medicaments containing nonaqueous vehicles, including N-methyl-2-pyrrolidone (NMP; CleaniCal), propylene glycol (PG; UltraCal XS), and polyethylene glycol (PEG; Calcipex II), were placed in the model.
Solution Casting Effect of PMMA-Based Polymer Electrolyte on the Performances of Solid-State Electrochromic Devices.
Polymers (Basel)
January 2025
Centre for Advanced Devices and Systems, Faculty of Engineering, Multimedia University, Persiaran Multimedia, Cyberjaya 63100, Selangor, Malaysia.
Electrochromic devices (ECDs) are devices that change their optical properties in response to a low applied voltage. These devices typically consist of an electrochromic layer, a transparent conducting substrate, and an electrolyte. The advancement in solid-state ECDs has been driven by the need for improved durability, optical performance, and energy efficiency.
View Article and Find Full Text PDFImproving the Electrochemical and Electrochromic Properties of Copolymerized 3,4-Ethylenedioxythiophene with Pyrene.
Polymers (Basel)
December 2024
School of Packaging and Materials Engineering, Hunan University of Technology, Zhuzhou 412007, China.
Pyrene (Pr) was used to improve the electrochemical and electrochromic properties of polythiophene copolymerized with 3,4-ethylenedioxythiophene (EDOT). The corresponding product, poly(3,4-ethylenedioxythiophene-co-Pyrene) (P(EDOT-co-Pr)), was successfully synthesized by electrochemical polymerization with different monomer concentrations in propylene carbonate solution containing 0.1 M lithium perchlorate (LiClO/PC (0.
View Article and Find Full Text PDFGram Negative Biofilms: Structural and Functional Responses to Destruction by Antibiotic-Loaded Mixed Polymeric Micelles.
Microorganisms
December 2024
Department of Microbiology, Stephan Angeloff Institute of Microbiology, Bulgarian Academy of Sciences, Akad. G. Bonchev Street, bl. 26, 1113 Sofia, Bulgaria.
Biofilms are a well-known multifactorial virulence factor with a pivotal role in chronic bacterial infections. Their pathogenicity is determined by the combination of strain-specific mechanisms of virulence and the biofilm extracellular matrix (ECM) protecting the bacteria from the host immune defense and the action of antibacterials. The successful antibiofilm agents should combine antibacterial activity and good biocompatibility with the capacity to penetrate through the ECM.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!