Aluminium and iron air pollution near an iron casting and aluminium foundry in Turin district (Italy).

J Inorg Biochem

Servizio di Medicina del Lavoro ASL 8, Via San Remigio 48, 10041 Carignano (TO), Italy.

Published: September 2007

This work reports the results of an environmental survey carried out in an industrial area in the Province of Turin: its main aim is to assess the levels of iron and aluminium in the outside air during the period from July to September to assess the influence of industrial activity (a cast-iron and aluminium foundry) which is interrupted during the month of August, on the level of metals present in the air. Conducting the analysis during this period of time made it possible to avoid the confounding effect of pollution due to domestic central heating. The measurements were taken from nine areas at different distances from the foundry in the area and according to the direction of the prevailing winds, as deduced from the historical data. The results of this survey show a statistically significant difference in iron and aluminium levels in the outside air in the geographic areas between the two main periods examined: during August (no foundry activity) v/s July-September (foundry activity). The values recorded are: Aluminium 0.4+/-0.45 microg/m(3) v/s 1.12+/-1.29 microg/m(3) (p<0.0001); Iron 0.95+/-0.56 microg/m(3) v/s 1.6+/-1.0 microg/m(3) (p<0.0001). There were no statistically significant differences between the nine sampling points from the point of view of the sampling sites, climate conditions and wind directions. We found no correlation with car traffic, in terms of the number of vehicles, and metals. The values of iron tended to be higher in the areas farther away from the foundry site in the areas located along the path of the prevailing winds.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jinorgbio.2007.06.012DOI Listing

Publication Analysis

Top Keywords

aluminium foundry
8
iron aluminium
8
foundry activity
8
aluminium
6
foundry
5
aluminium iron
4
air
4
iron air
4
air pollution
4
pollution iron
4

Similar Publications

The article addresses stress formation in the structural 3D-printed elements of a high-pressure die casting die mould used for production of aluminum castings. The 3D-printed elements with conformal cooling are manufactured of 18Ni300 powder. Initial numerical calculations were performed on a test die mould made of standard steel X40CrMoV5 to determine temperature distribution and stress state, providing a baseline for comparing 3D-printed 18Ni300 parts.

View Article and Find Full Text PDF

High-pressure die casting (HPDC) of aluminum alloys is one of the most efficient manufacturing methods, offering high repeatability and the ability to produce highly complex castings. The cast parts are characterized by good surface quality, high dimensional accuracy, and high tensile strength. Continuous technological advancements are driving the increase in part complexity and quality requirements.

View Article and Find Full Text PDF

Reduction of iron in high-phosphorus oolitic ore from the Lisakovsk deposit using solid carbon, carbon monoxide, and hydrogen. An X-ray phase analysis was used to determine the phase composition of the samples after reduction roasting. When reduced with carbon monoxide or hydrogen, α-iron appears in the samples, while phosphorus remains in the form of iron, calcium, and aluminum phosphates.

View Article and Find Full Text PDF

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation.

Materials (Basel)

August 2024

Key Laboratory of Automobile Materials, Ministry of Education and Department of Materials Science and Engineering, Jilin University, Renmin Street No. 5988, Changchun 130025, China.

Al-Mg alloys are widely used as important engineering structural materials in aerospace engineering, transportation systems, and structural constructions due to their low density, high specific strength, corrosion resistance, welding capability, fatigue strength, and cost-effectiveness. However, the conventional Al-Mg alloys can no longer fully satisfy the demands of practical production due to difficulties caused by many defects. The high strength of Al-Mg alloys as non-heat treatment precipitation-strengthened alloys is achieved primarily by solid solution strengthening along with work hardening rather than precipitation strengthening.

View Article and Find Full Text PDF
Article Synopsis
  • Micronucleus (MN) assays using buccal cells are effective for assessing genetic damage in workers exposed to genotoxic metals, with most studies showing increased MN and nuclear anomalies among various occupations.
  • A comprehensive review of 73 studies, mainly from South East Asia and South America, highlighted the need for better evaluation methods, as many studies lacked thorough assessments of genetic stability and cytotoxic effects.
  • The data suggests that MN assays can provide valuable insights into chromosomal damage from metal exposure, complementing current chemical analysis and potentially enhancing workplace safety by reflecting biological impacts.
View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!