Theory is presented to describe the voltammetric signals associated with the stripping phase of stripping voltammetry at solid electrodes. Three mathematical models are considered, and the importance of the hemispherical diffusion associated with electrochemical dissolution of particles in the micrometer range is investigated. Model A considers a "monolayer" system where the coverage at a specific point cannot exceed a maximum value. Model B considers a thin layer of metal or metal oxide, but in contrast to model A, the maximum surface coverage is not restricted. Model C represents the stripping of a "thick layer" where the deposition is also unrestricted.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/ac070046b | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Exploring wood-derived biochar potential for electrochemical sensing of fungicides mancozeb and maneb in environmental water samples.
Talanta
January 2025
Department of Chemistry, Biochemistry and Environmental Protection, Faculty of Sciences, University of Novi Sad, Trg D. Obradovića 3, 21000, Novi Sad, Serbia.
The sustainable material, biochar (BC) from a hardwood source, was synthesized via pyrolysis process at 400 °C (BC400) and 700 °C (BC700) and used as a modifier during the electrochemical sensor design. The prepared BCs were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) analysis, and elemental analysis (CHNS). The development of rapid analytical techniques for detecting pesticides employing a low-cost carbon paste electrode (CPE) modified with BC is a novel strategy to provide a sensitive response to water pollution.
View Article and Find Full Text PDFNew Long-Term Use Solid Bismuth Microelectrode Arrays for Rapid and Sensitive Determination of Sunset Yellow in Isotonic Beverages and Water Samples by Adsorptive Stripping Voltammetry.
Molecules
January 2025
Institute of Chemical Sciences, Faculty of Chemistry, Maria Curie Sklodowska University, 20-031 Lublin, Poland.
This article reports on the long-term use, solid bismuth microelectrode arrays for the first time. The presented working microelectrode is characterized by particular advantages compared to bismuth film electrodes and solid single bismuth microelectrodes; these advantages include environmentally friendly properties and the amplification of recorded currents, which are subsequently more resistant to interference. The proposed solid bismuth microelectrode array was applied to develop an adsorptive stripping voltammetric procedure for Sunset Yellow determination.
View Article and Find Full Text PDFrGO/HfO nanocomposite-enabled electrochemical sensor for high-performance pesticide detection.
Talanta
January 2025
Department of Chemical and Biomolecular Engineering, University of Connecticut, CT, 06269, United States. Electronic address:
This study applies a periodic table-guided approach to select and investigate hafnium oxide (HfO), in conjunction with reduced graphene oxide (rGO), for the electrochemical determination of methyl parathion (MP), an organophosphate insecticide. MP poses significant ecological and health risks due to its high toxicity, and despite bans, illegal use has been reported, especially in the global south. To address these challenges, an electrode modified with a nanocomposite of rGO/HfO was first constructed for MP detection.
View Article and Find Full Text PDFEnhanced simultaneous voltammetric detection of lead, copper, and mercury using a MIL-101(Cr)-(COOH)@MWCNTs modified glassy carbon electrode.
Anal Chim Acta
February 2025
Chemistry Department, Faculty of Science, Ain-Shams University, Cairo, 11566, Egypt; Department of Chemistry, Faculty of Science, Galala University, New Galala City, Suez, Egypt. Electronic address:
Background: Electrochemical methods, particularly those utilizing sensors, offer distinct advantages over classical analytical methods. They are cost-effective, compatible with mass fabrication, suitable for remote sensing, and can be designed as handheld analyzers. In this context, MIL-101(Cr)-(COOH)₂@MWCNTs was utilized for the first time as a modifier for GCE for the sensitive voltammetric detection of Pb(II), Cu(II), and Hg(II).
View Article and Find Full Text PDFOptimizing the Construction and Activation of 3D-Printed Electrochemical Sensors: An Experimental Design Approach for Simultaneous Electroanalysis of Paracetamol and Caffeine.
ACS Omega
January 2025
Laboratory of Carbon and Ceramic Materials (LMC), Department of Physics, Center of Exact Sciences, Federal University of Espírito Santo, Vitória 29075-910, Espírito Santo, Brazil.
This work presents an optimization of the construction, treatment, and activation of 3D-printed electrochemical sensors (E-3D). For this, was used a 2-full factorial design examining three key variables at two levels: electrode height, electrode diameter, and printing speed. Moreover, it evaluates various physical, chemical, and electrochemical methods to treat and activate the E-3D surface.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!