Performance Evaluation of Telemedicine System based on multicasting over Heterogeneous Network.

Conf Proc IEEE Eng Med Biol Soc

Yonsei University, Seoul, Korea (phone: 822-222-81922; fax: 822-361-9923; e-mail:

Published: October 2012

For appropriate diagnosis, medical image such as high quality image of patient's affected part and vital signal, patient information, and teleconferencing data for communication between specialists will be transmitted. After connecting patient and specialist the center, sender acquires patient data and transmits to the center through TCP/IP protocol. Data that is transmitted to center is retransmitted to each specialist side that accomplish connection after being copied according to listener's number from transmission buffer. At transmission of medical information data in network, transmission delay and loss occur by the change of buffer size, packet size, number of user and kind of networks. As there lies the biggest delay possibility in ADSL, buffer Size should be established by 1Mbytes first to minimize transmission regionalism and each packet's size must be set accordingly to MTU Size in order to improve network efficiency by maximum. Also, listener's number should be limited by less than 6 people. Data transmission consisted smoothly all in experiment result in common use network- ADSL, VDSL, WLAN, LAN-. But, possibility of delay appeared most greatly in ADSL that has the most confined bandwidth. To minimize the possibility of delay, some adjustment is needed such as buffer size, number of receiver, packet size.

Download full-text PDF

Source
http://dx.doi.org/10.1109/IEMBS.2005.1616893DOI Listing

Publication Analysis

Top Keywords

buffer size
12
listener's number
8
packet size
8
size number
8
possibility delay
8
size
7
data
5
transmission
5
performance evaluation
4
evaluation telemedicine
4

Similar Publications

By evaluating the stability profiles of each component of a vaccine candidate (antigens, adjuvants), formulation conditions to mitigate vaccine instability can be identified. In this work, two recombinant Cytomegalovirus (CMV) glycoprotein antigens (gB, Pentamer) were formulated with SPA14, a novel liposome-based adjuvant system containing a synthetic TLR4 agonist (E6020) and a saponin (QS21). Analytical characterization and accelerated stability studies were performed with the two CMV antigens, formulated with and without SPA14, under various conditions (temperature, pH, excipients).

View Article and Find Full Text PDF

Poly-N-isopropylacrylamide (PNIPAm), a thermorresponsive polymer, highly soluble in water below its lower critical solution temperature (LCST), is widely used in biomedical applications like drug delivery. Being able to measure PNIPAm size and aggregation state in solution quickly, inexpensively, and accurately below the LCST is critical when stoichiometric particle or molecular ratios are required. Dynamic light scattering (DLS) is probably the most widely available, and inexpensive nanoparticle sizing technique, but there are limitations with respect to sample polydispersity.

View Article and Find Full Text PDF

Post-translational modifications (PTMs) of proteins dynamically build the buffering and adapting interface between oncogenic mutations and environmental stressors, on the one hand, and cancer cell structure, functioning, and behavior. Aberrant PTMs can be considered as enabling characteristics of cancer as long as they orchestrate all malignant modifications and variability in the proteome of cancer cells, cancer-associated cells, and tumor microenvironment (TME). On the other hand, PTMs of proteins can enhance anticancer mechanisms in the tumoral ecosystem or sustain the beneficial effects of oncologic therapies through degradation or inactivation of carcinogenic proteins or/and activation of tumor-suppressor proteins.

View Article and Find Full Text PDF

'Ship-in-a-Bottle' Integration of pH-Sensitive 3D Proteinaceous Meshes into Microfluidic Channels.

Nanomaterials (Basel)

January 2025

Innovative Laser Processing Group, Research Institute for Advanced Electronics and Photonics, National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba 305-8568, Ibaraki, Japan.

Microfluidic sensors incorporated onto chips allow sensor miniaturization and high-throughput analyses for point-of-care or non-clinical analytical tools. Three-dimensional (3D) printing based on femtosecond laser direct writing (fs-LDW) is useful for creating 3D microstructures with high spatial resolution because the structures are printed in 3D space along a designated laser light path. High-performance biochips can be fabricated using the 'ship-in-a-bottle' integration technique, in which functional microcomponents or biomimetic structures are embedded inside closed microchannels using fs-LDW.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!