In the context of our detailed study of the chemical behavior of aquo- and ammine-Zn(II) complexes, ab initio quantum mechanical/molecular mechanical (QM/MM) molecular dynamics (MD) simulations were performed at the Hartree-Fock (HF) level for the zinc(II)-diamine complexes in aqueous solution. The initial structures of cis and trans isomers of the tetraaquodiamminezinc(II) complex were found to transform into the triaquodiamminezinc(II) complex by releasing one water ligand after approximately 6 and approximately 22 ps of simulation time, respectively. The structural and dynamical properties of these three zinc complexes, i.e., cis-[Zn(NH3)2(H2O)4]2+, trans-[Zn(NH3)2(H2O)4]2+, and [Zn(NH3)2(H2O)3]2+, were analyzed in terms of radial distribution functions (RDF), coordination number distributions (CND), angular distribution functions (ADF), tilt and theta angle distributions, ligands' mean residence times (MRTs), and ion-ligand stretching frequencies. One considerably elongated Zn-O bond of 2.43 A was observed in the case of the cis isomer for one of the water ligands located in the trans position to an ammonia ligand. In the trans isomer the average Zn-O bond length was observed to be 2.23 A, while in the triaquodiamminezinc(II) complex two distinct Zn-O bonds, namely 2.12 A for the ligands in the trigonal plane and 2.26 A for axial water molecules, were observed. As both of the octahedral isomers are transformed into the pentacoordinated structure within the picosecond range, they might be regarded as "metastable species or intermediates", while the triaquodiamminezinc(II) complex is the most stable species of the zinc(II)-diamine complex in aqueous solution.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/jp0654213 | DOI Listing |
Environ Sci Pollut Res Int
January 2025
Grupo de Investigación Materiales Con Impacto (Mat&Mpac), Facultad de Ciencias Básicas, Universidad de Medellín, Carrera 87 No. 30-65, 050026, Medellín, Colombia.
This study shows the efficiency of WH-C450, an adsorbent obtained from water hyacinth (WH) biomass, in the removal of sulfamethoxazole (SMX) from aqueous solutions. The process involves calcination of WH at 450 °C to produce an optimal adsorbent material capable of removing up to 73% of SMX and maximum SMX adsorption capacity of 132.23 mg/g.
View Article and Find Full Text PDFSci Rep
January 2025
Department of Biological Sciences, Birla Institute of Technology and Sciences, Pilani, 333031, Rajasthan, India.
In present study, 15 morphologically different fungi isolated from rhizopheric soils of an industrial area were screened for their Zn removal efficiency from aqueous solution. Isolate depicting highest potential was molecularly identified as Aspergillus terreus SJP02. Effect of various process parameters viz.
View Article and Find Full Text PDFSci Rep
January 2025
Chemistry Department, Faculty of Science, Tanta University, Tanta, 31527, Egypt.
Three composites based on Poly (meta-aminophenol) (PmAP), (3-aminopropyl) triethoxysilane (APTES) and graphene oxide (GO) were synthesized with initial GO dispersion of 3.3, 6.6, and 9.
View Article and Find Full Text PDFJ Am Chem Soc
January 2025
State Key Laboratory of Materials-Oriented Chemical Engineering, College of Chemical Engineering, Nanjing Tech University, Nanjing 211816, China.
Metal-nonaqueous solution interfaces, a key to many electrochemical technologies, including lithium metal batteries, are much less understood than their aqueous counterparts. Herein, on several metal-nonaqueous solution interfaces, we observe capacitances that are 2 orders of magnitude lower than the usual double-layer capacitance. Combining electrochemical impedance spectroscopy, atomic force microscopy, and physical modeling, we ascribe the ultralow capacitance to an interfacial layer of 10-100 nm above the metal surface.
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
Division of Micro and Nanosystems (MST), School of Electrical Engineering and Computer Science (EECS), KTH Royal Institute of Technology, Stockholm SE-10044, Sweden.
Controlled breakdown has emerged as an effective method for fabricating solid-state nanopores in thin suspended dielectric membranes for various biomolecular sensing applications. On an unpatterned membrane, the site of nanopore formation by controlled breakdown is random. Nanopore formation on a specific site on the membrane has previously been realized using local thinning of the membrane by lithographic processes or laser-assisted photothermal etching under immersion in an aqueous salt solution.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!