Unlabelled: Rapid induction of a profound hypothermic state (suspended animation) can maintain viability of key organs during repair of lethal injuries. Conventional cardiopulmonary bypass equipment (roller pump) used to induce and reverse hypothermia is expensive, bulky, requires standard electricity, and is not transportable. Development of a small, portable, battery operated, disposable, pump can logistically facilitate induction and maintenance of hypothermia. In this experiment, a portable prototype pump was tested and its performance was compared with the regular roller pump in a swine model of lethal vascular injuries.
Methods: Uncontrolled hemorrhage was induced in 16 swine (80-120 lbs) by creating an iliac artery and vein injury (nonlethal). After 30 minutes of pulseless shock, the descending thoracic aorta was lacerated (lethal injury). Through a left thoracotomy approach, a catheter was placed in the aorta and cold organ preservation solution was infused to rapidly (2 degrees C/min) induce hypothermia (10 degrees C) for 60 minutes. The performance of the prototype pump was initially tested in a nonsurvival experiment (four animals). Then, 12 animals were cooled either with (n = 6/group) (1) conventional roller pump or (2) small prototype pump. The injuries were repaired during hypothermic arrest and the animals were re-warmed (0.5 degrees C/min). Whole blood was infused during resuscitation on cardiopulmonary bypass. Surviving animals were closely monitored for 3 weeks for postoperative complications, neurologic deficits, and organ dysfunction.
Results: The flow rates and the time needed to induce and reverse profound hypothermia were no different between the prototype and the conventional roller pumps. Three-week survival rates were 83% in both groups. Only a transient increase in liver enzymes, and markers of cellular injury (creatine kinase, lactate dehydrogenase) was noted (no meaningful difference between groups), with no long-term organ dysfunction.
Conclusions: In this large animal model of lethal vascular injuries, a portable, battery operated, disposable, rotary pump performed as well as the conventional roller pump. The logistical advantages of this system make it an attractive choice for inducing hypothermia in emergency departments and austere settings, and for maintaining hypothermia during transport.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1097/01.ta.0000244414.76523.d8 | DOI Listing |
Artif Organs
October 2024
ARTORG Center for Biomedical Engineering Research, University of Bern, Bern, Switzerland.
Bioinspir Biomim
October 2024
Department of Biomedical Engineering, Seoul National University College of Medicine, 103, Daehak-ro, Jongno-gu, Seoul 03080, Republic of Korea.
Soft peristaltic pumps, which use soft ring actuators instead of mechanical pistons or rollers, offer advantages in transporting liquids with non-uniform solids, such as slurry, food, and sewage. Recent advances in 3D printing with flexible thermoplastic polyurethane (TPU) present the potential for single-step fabrication of these pumps, distinguished from handcrafted, multistep traditional silicone casting methods. However, because of the relatively high hardness of TPU, TPU-based soft peristaltic pumps contract insufficiently and thus cannot perform as well as silicone-based ones.
View Article and Find Full Text PDFInterdiscip Cardiovasc Thorac Surg
September 2024
Department of Anaesthesia and Intensive Care, Institute of Clinical Sciences, Sahlgrenska Academy, University of Gothenburg, Gothenburg, Sweden.
Objectives: Extracorporeal circulation induces pronounced effects on haemostasis and rheology. To study these, an ex vivo simulation model is an attractive alternative but often requires large amounts of blood. We sought to create a miniaturized roller pump circuit requiring minimal amounts of blood and to test if the circuit could be used to compare coagulation, platelet function and blood rheology between a dextran-based and a crystalloid-based priming solution.
View Article and Find Full Text PDFArtif Organs
January 2025
Center for Devices and Radiological Health, U.S. Food and Drug Administration, Silver Spring, Maryland, USA.
Background: To accommodate a wider range of medical device sizes, a larger in vitro flow loop thrombogenicity test system using 9.5 -mm inner diameter (ID) tubing was developed and evaluated based on our previously established 6.4 -mm ID tubing system.
View Article and Find Full Text PDFEur J Cardiothorac Surg
July 2024
Department of Cardiac Surgery, Anthea Hospital, Bari, Italy.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!