Strongly interacting low-viscosity matter created in relativistic nuclear collisions.

Phys Rev Lett

Section for Theoretical Physics, Department of Physics, University of Bergen, Allegaten 55, 5007 Bergen, Norway.

Published: October 2006

Substantial collective flow is observed in collisions between large nuclei at BNL RHIC (Relativistic Heavy Ion Collider) as evidenced by single-particle transverse momentum distributions and by azimuthal correlations among the produced particles. The data are well reproduced by perfect fluid dynamics. A calculation of the dimensionless ratio of shear viscosity eta to entropy density s by Kovtun, Son, and Starinets within anti-de Sitter space/conformal field theory yields eta/s=variant Planck's over 2pi/4pikB, which has been conjectured to be a lower bound for any physical system. Motivated by these results, we show that the transition from hadrons to quarks and gluons has behavior similar to helium, nitrogen, and water at and near their phase transitions in the ratio eta/s. We suggest that experimental measurements can pinpoint the location of this transition or rapid crossover in QCD.

Download full-text PDF

Source
http://dx.doi.org/10.1103/PhysRevLett.97.152303DOI Listing

Publication Analysis

Top Keywords

interacting low-viscosity
4
low-viscosity matter
4
matter created
4
created relativistic
4
relativistic nuclear
4
nuclear collisions
4
collisions substantial
4
substantial collective
4
collective flow
4
flow observed
4

Similar Publications

Article Synopsis
  • Cemented natural fractures (CNFs) in shale and tight sandstone reservoirs can significantly influence hydraulic fracturing and oil/gas production, but their interaction mechanisms are not fully understood.
  • A numerical model using the particle flow method was developed to simulate hydraulic fracture propagation and its interaction with CNFs, showing reliable results that align with previous experimental data.
  • The study found that factors like CNF cementation strength, inclination angle, and fluid viscosity can alter fracture propagation patterns, including new behaviors like bifurcation fractures and the development of complex fracture networks.
View Article and Find Full Text PDF

During deepwater drilling, the low mudline temperatures and narrow safe density window pose serious challenges to the safe and efficient performance of deepwater water-based drilling fluids. Low temperatures can lead to physical and chemical changes in the components of water-based drilling fluids and the behavior of low temperature gelation. As a coarse dispersion system, water-based drilling fluid has a complex composition of dispersed phase and dispersing medium.

View Article and Find Full Text PDF

The impact of active substance on the adhesiveness of medicated patches containing liquid additives.

Eur J Pharm Sci

December 2024

Department of Pharmaceutical Technology, Faculty of Pharmacy, Medical University of Gdansk, Hallera av. 107, Gdansk 80-402, Poland.

Adhesiveness of dermal patches can be modified in the presence of active substances. The effect is more complex when liquid components are also present in the matrix. Commercial grade pressure sensitive adhesive (PSA) polyacrylates (three types) and silicones (two types) were used to prepare adhesive matrices and liquid additives were propylene glycol, polyoxyethylene glycol, isopropyl myristate, triacetin, triethyl citrate or low viscosity silicone oil.

View Article and Find Full Text PDF

Preparation and Evaluation of a Novel Branched Polymer as Thickener for Calcium Chloride-Based Drilling and Completion Fluids.

Molecules

November 2024

National Engineering Research Center for Colloidal Materials, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100, China.

Calcium halide-based fluids are often used in drilling and completion operations due to their high density, clay inhibition and low solid content. However, there is a lack of thickeners to promote gel strength, which improves the fluid's capacity to carry and suspend cuttings. To solve this problem, the branched polymer (hereafter abbreviated as PAD-B) was prepared by the copolymerization of N,N-dimethylacrylamide (DMAM) and 2-acrylamide-2-methylpropane sulfonic acid (AMPS), using polyethylenimine as a branching agent and cerium ammonium nitrate as the initiator.

View Article and Find Full Text PDF

Background: To overcome the deficiency of pure starch in film-forming performance, ionic liquids (ILs) have been introduced when preparing a homogeneous blend of starch and fiber. It is essential to select the appropriate ratio of starch to fiber and evaluate the film-forming property of the resulted composites. In the present study, 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) was used to prepare composites of soybean fiber (SF) and corn starch (CS) at various ratios.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!