Transport properties such as ionic conductivity, lithium transference number, and apparent salt diffusion coefficient are reported for solid polymer electrolytes (SPEs) prepared using several oligomeric bis[(perfluoroalkyl)sulfonyl]imide (fluorosulfonimide) lithium salts dissolved in high molecular weight poly(ethylene oxide) (PEO). The salt series consists of polyanions in which two discrete fluorosulfonimide anions are linked together by [(perfluorobutylene)disulfonyl]imide linker chains. The restricted diffusion technique was used to measure the apparent salt diffusion coefficients in SPEs, and cationic transference numbers were determined using both potentiostatic polarization and electrochemical impedance spectroscopy methods. A general trend of diminished salt diffusion coefficient with increasing anion size was observed and is opposite to the trend observed in ionic conductivity. This unexpected finding is rationalized in terms of the cumulative effects of charge carrier concentration, anion mobility, ion pairing, host plasticization by the anions, and salt phase segregation on the conductivity.

Download full-text PDF

Source
http://dx.doi.org/10.1021/jp062648pDOI Listing

Publication Analysis

Top Keywords

salt diffusion
12
transport properties
8
solid polymer
8
polymer electrolytes
8
prepared oligomeric
8
fluorosulfonimide lithium
8
lithium salts
8
salts dissolved
8
dissolved high
8
high molecular
8

Similar Publications

Tailoring Acid-Salt Hybrid Electrolyte Structure for Stable Proton Storage at Ultralow Temperature.

Adv Mater

December 2024

Hefei National Research Center for Physical Sciences at the Microscale, Department of Materials Science and Engineering, CAS Key Laboratory of Materials for Energy Conversion, University of Science and Technology of China, Hefei, Anhui, 230026, P. R. China.

The critical challenges in developing ultralow-temperature proton-based energy storage systems are enhancing the diffusion kinetics of charge carriers and inhibiting water-triggered interfacial side reactions between electrolytes and electrodes. Here an acid-salt hybrid electrolyte with a stable anion-cation-HO solvation structure that realizes unconventional proton transport at ultralow temperature is shown, which is crucial for electrodes and devices to achieve high rate-capacity and stable interface compatibility with electrodes. Through multiscale simulations and experimental investigations in the electrolyte employing ZnCl introduced into 0.

View Article and Find Full Text PDF

The growing demand for clean, decentralized energy has increased interest in blue energy, which generates power from water with different salt concentrations. Despite its potential as a renewable, low-cost energy source, optimizing electrode materials remains a challenge. This work presents a nanomaterial developed via microwave-assisted sol-gel methodology for blue energy applications, where ion diffusion and charge storage are critical.

View Article and Find Full Text PDF

Polyelectrolyte hydrogels are smart materials whose swelling behavior is governed by ionizable groups on their polymeric chains, making them sensitive to pH and ionic strength. This study combined experiments and modeling to characterize anionic hydrogels. Mechanical tests and gravimetric analyses were performed to track hydrogel mass over time and at a steady state under varying pH and salt concentrations.

View Article and Find Full Text PDF

Carboxymethyl cellulose sodium salt (CMC)-based superabsorbents are promising materials for the development of agricultural matrices aimed at water management and slow-release fertilizer production. However, an increase in the CMC content tends to reduce their water-absorbing capacity. This study aims to develop a cost-effective method for producing eco-friendly superabsorbents with enhanced water-absorbing capacity by incorporating a porogen and employing lyophilization.

View Article and Find Full Text PDF

Environmentally friendly nanoporous gels are tailor-designed and employed in the adsorption of toxic organic pollutants in wastewater. To ensure the maximum adsorption of the contaminant molecules by the gels, molecular modeling techniques were used to evaluate the binding affinity between the toxic organic contaminants such as methylene blue (MB) and Congo red (CR) and various biopolymers. To generate nanopores in the matrix of the polymeric gels, salt crystals were used as porogen.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!