Electron backscatter diffraction was used to examine the recrystallization behaviour of warm, clock-rolled uranium. A new uranium preparation method was developed, resulting in acceptable specimen surface finishes nearly every time, even for as-rolled specimens. Recrystallized fractions were differentiated from unrecrystallized fractions using differences in the grain average misorientation, a measure of the internal level of misorientation within a grain. This new approach better estimates the recrystallized fraction than hardness measurements, and has the advantage over standard metallographic techniques of providing texture information.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/j.1365-2818.2006.01595.x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Titanium Oxide Formation in TiCoCrFeMn High-Entropy Alloys.
Materials (Basel)
January 2025
Faculty of Advanced Technologies and Chemistry, Military University of Technology, Sylwestra Kaliskiego 2, 00-908 Warsaw, Poland.
High-entropy materials, characterized by complex chemical compositions, are difficult to identify and describe structurally. These problems are encountered at the composition design stage when choosing an effective method for predicting the final phase structure of the alloy, which affects its functional properties. In this work, the effects of introducing oxide precipitates into the matrix of a high-entropy TiCoCrFeMn alloy to strengthen ceramic particles were studied.
View Article and Find Full Text PDFCrystal and Dislocation Characteristics of Ti-6Al-4V Alloy Under Effect of Laser Shock Peening.
Materials (Basel)
January 2025
College of Materials Science and Engineering, Chongqing University, Chongqing 400045, China.
Laser shock peening (LSP) is an effective method for enhancing the fatigue life and mechanical properties of Ti alloys. However, there is limited research on the effects of LSP on crystal structure and dislocation characteristics. In this study, Ti-6Al-4V alloy was subjected to laser shock peening with varying laser power levels.
View Article and Find Full Text PDFEffects of Pre-Deformation in Corrosion Fatigue Crack Growth of Al-Mg-Zn Alloy.
Materials (Basel)
January 2025
State Key Laboratory of Precision Manufacturing for Extreme Service Performance, Central South University, Changsha 410083, China.
This study investigated the effect of pre-deformation on the corrosion fatigue crack propagation (CFCG) of Al-Mg-Zn alloy in a corrosive environment. Tensile tests at different pre-deformation levels and molecular dynamics simulations analyzed changes in dislocation density. Corrosion fatigue experiments were conducted in a 3.
View Article and Find Full Text PDFBilayer TiO/Mo-BiVO Photoelectrocatalysts for Ibuprofen Degradation.
Materials (Basel)
January 2025
Section of Condensed Matter Physics, Department of Physics, National and Kapodistrian University of Athens, University Campus, 15784 Athens, Greece.
Heterojunction formation between BiVO nanomaterials and benchmark semiconductor photocatalysts has been keenly pursued as a promising approach to improve charge transport and charge separation via interfacial electron transfer for the photoelectrocatalytic degradation of recalcitrant pharmaceutical pollutants. In this work, a heterostructured TiO/Mo-BiVO bilayer photoanode was fabricated by the deposition of a mesoporous TiO overlayer using the benchmark P25 titania catalyst on top of Mo-doped BiVO inverse opal films as the supporting layer, which intrinsically absorbs visible light below 490 nm, while offering improved charge transport. A porous P25/Mo-BiVO bilayer structure was produced from the densification of the inverse opal underlayer after post-thermal annealing, which was evaluated on photocurrent generation in aqueous electrolyte and the photoelectrocatalytic degradation of the refractory anti-inflammatory drug ibuprofen under back-side illumination by visible and UV-Vis light.
View Article and Find Full Text PDFEffect of Tool Shoulder Profile on Grain and Texture Development in the Weld Interface Zone of Friction-Stir-Welded Dissimilar AA2024/AA7075 Joints.
Materials (Basel)
January 2025
College of Intelligent Manufacturing, Huanghuai University, Zhumadian 463000, China.
Friction-stir-welded dissimilar AA2024/AA7075 joints have an apparent influence on grain and texture development at the weld interface due to differences in physical and chemical properties between the two aluminum alloys. In this work, the effect of tool shoulder profile on grain structure and texture evolution in the center interface zone (CIZ) and bottom interface zone (BIZ) of dissimilar AA2024/AA7075 joints were quantitatively studied by electron back-scattering diffraction (EBSD). The results indicate that abundant fine and coarse equiaxial grains are produced in the CIZ and BIZ of the joints produced with a concentric circle shoulder (CCS) and three-helix shoulder (THS), and the average grain size of the BIZ is lower than that of the CIZ for the same CCS or THS joint.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!