The interfacial tension gamma of the hexane solution of 1H,1H-perfluorononanol (FDFC(9)OH) and its omega-hydrogenated analogue, 1H,1H,9H-perfluorononanol (HDFC(9)OH), against water was measured as a function of pressure and concentration at 298.15 K in order to clarify the effect of omega-dipole on the orientation of fluorononanol molecules from the viewpoint of volume. The adsorbed films of both alcohols exhibit two kinds of phase transitions among three different states: the gaseous, expanded, and condensed states. The partial molar volume changes of adsorption - in the expanded and condensed states were evaluated and compared between the two systems. The - values of both alcohols are negative, and thus the alcohol molecules have smaller volume in the adsorbed film than in the bulk solution. Furthermore, the value was obtained through the evaluation of by the density measurement of the bulk hexane solution. It was found that the value of HDFC(9)OH is smaller than that of FDFC(9)OH in the condensed state. On the basis of three matters concerning the molecular structure of alcohols, the occupied area at the interface, and the orientation of FDFC(9)OH in the adsorbed film deduced from the earlier results of X-ray reflectivity measurement, the mean tilt angle of HDFC(9)OH from the interface normal in the condensed film was estimated to be 15 degrees . The thermodynamic estimation demonstrated here is highly valuable one to provide structure information on an adsorbed film.

Download full-text PDF

Source
http://dx.doi.org/10.1021/jp0581375DOI Listing

Publication Analysis

Top Keywords

adsorbed film
12
adsorption fluorononanols
8
hexane solution
8
volume adsorbed
8
expanded condensed
8
condensed states
8
omega-hydrogenation adsorption
4
fluorononanols hexane/water
4
hexane/water interface
4
interface pressure
4

Similar Publications

The textural properties of synthetic and natural clays in the sodium form and exchanged with tetramethylammonium cations (TMA) were characterized using N and Ar physisorption isotherms at cryogenic temperatures. Specific surface areas and micro/mesoporous volumes were determined using the BET and the models. The analysis requires the use of reference isotherms measured at the same temperature on the surface of non-porous materials with an identical chemical composition.

View Article and Find Full Text PDF

Fly ash, produced during coal combustion for energy making, which is recognized as an industrial by-product, could lead to environmental health hazards. Subsequently, fly ash found that an exceptional adsorption performance for the removal of various toxic pollutants, the adsorption capacity of fly ash might be altered by introducing physical/chemical stimulation. Successfully converting fly ash into zeolites not only recovers their disposal difficulties but also transforms unwanted materials into merchandisable products for various industrial applications.

View Article and Find Full Text PDF

A poly(vinyl alcohol)/montmorillonite/titania (PVA/MMT/TiO) nanocomposite film was fabricated via a simple solution casting strategy for the removal of cationic as well as anionic dyes. The developed nanocomposite film was subjected to X-ray diffraction (XRD), Fourier transform Infrared (FTIR), thermogravimetric analysis, dynamic mechanical analysis (DMA), mechanical property evaluation, and scanning electron microscopy (SEM) analysis. The embedding of MMT and TiO nanoparticles onto a PVA matrix has been confirmed from XRD, FTIR, and SEM analysis.

View Article and Find Full Text PDF
Article Synopsis
  • The study explored modifying polyvinyl alcohol/chitosan (PVA/CS) membranes with a deep eutectic solvent (DES) to improve their strength and ability to adsorb brilliant green dye.
  • Incorporating 5% DES significantly increased the mechanical properties, with elongation at break rising from 8.176% to 22.817%, and the DES-modified membranes showed much higher dye adsorption capacity (124.63 mg/g) compared to the unmodified ones (23.15 mg/g).
  • Machine learning models revealed that the random forest model had better predictive accuracy for the adsorption process than the artificial neural network, while density functional theory calculations supported the improvements in adsorption energy with the use of DES.
View Article and Find Full Text PDF

This research aims to design a novel selective and multifunctional adsorbent based on Al/Cu modified hemp fibres as a novel and multifunctional adsorbent for removing different classes of pollutants. The adsorbent, which was widely characterized, was shown to be more effective in removing anionic dyes compared to cationic ones. Among the tested dye, methyl orange was selected to understand how different parameters, such as temperature (20-80°C), contact time, pH (2-12), initial dye concentration (50-300 ppm), salinity and adsorbent dosage (1-10 g/L) affect the removal capacity.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!