Purpose: Despite the different light sources and polymerization techniques developed to eliminate it, microleakage of resin composite still remains a problem. This in vitro study was designed to compare the effects of exponential mode soft-start polymerization with those of standard and high-intensity continuous light polymerization on microleakage in Class II resin composite restorations.
Materials And Methods: Standardized Class II cavities (4 mm wide, 4 mm long, 5 to 6 mm high, 2 mm deep) were prepared in 50 extracted human molars. Specimens were divided into 5 groups (n = 10) and restored using the same hybrid resin composite (Z250), but separately polymerized by one of five different methods: group 1: continuous halogen light polymerization for 40 s; group 2: continuous high-intensity halogen light polymerization for 10 s; group 3: exponential mode soft-start halogen light polymerization for a total of 40 s; group 4: continuous LED light polymerization for 40 s; Group 5: exponential mode soft-start LED light polymerization for a total of 40 s. All specimens were thermocycled for 1000 cycles at 5 degrees C to 55 degrees C and then placed in 0.5% basic fuchsin dye for 24 h. Specimens were then rinsed, embedded in resin and sectioned longitudinally. Dye penetration at occlusal and cervical margins was rated using a scale of 0 to 4. Data was analyzed using Kruskal-Wallis and Mann-Whitney U-tests.
Results: Significantly lower marginal leakage was recorded with exponential mode soft-start polymerization when compared to continuous light polymerization. No significant differences in microleakage were observed between LED and halogen light polymerization.
Conclusion: Within the limits of this in vitro study, the use of the soft-start exponential mode of LED and/or halogen light units in the polymerization of hybrid composite was found to produce significantly lower microleakage at both occlusal and cervical margins when compared to continuous light polymerization methods.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
Upcycling industrial peach waste to produce dissolving pulp.
Environ Sci Pollut Res Int
January 2025
Laboratory of Design and Development of Innovative Knitted Textiles and Garments, Department of Industrial Design and Production Engineering, University of West Attica, 12244, Egaleo, Attica, Greece.
This study investigates the production of high-purity cellulose pulp from peach (Prunus persica) fruit wastes generated during the processing of a Greek compote and juice production industry. A three-step chemical process is used, including alkaline treatment with NaOH, organic acid (acetic and formic) treatment, and hydrogen peroxide treatment, with the goal of cellulose extraction and purification. A fractional factorial design optimized reagent levels, revealing the strong influence of NaOH concentration on α-cellulose content and degree of polymerization.
View Article and Find Full Text PDFConstructing a built-in electric field by grafting strong electronegative small molecules for photocatalytic H production.
Chem Commun (Camb)
January 2025
Engineering Research Center of Ministry of Education for Geological Carbon Storage and Low Carbon Utilization of Resources, Beijing Key Laboratory of Materials Utilization of Nonmetallic Minerals and Solid Wastes, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences (Beijing), Beijing 100083, China.
Asymmetric carbon nitride (FCN) is developed by grafting strong electronegative small molecules onto CN. The introduction of these small molecules enhances the visible light absorption range and redistributes the charge density. Combining DRS, KPFM, and DFT results, it is revealed that the strong built-in electric field and the effective spatial separation of redox sites contribute to the directional charge separation and migration for superior photocatalytic H evolution.
View Article and Find Full Text PDFCase Report: First use of dental bisphenol A-glycidyl methacrylate composite without UV light polymerization for repair of iatrogenic CSF leak following a frontal craniotomy plus tumor resection.
Front Surg
January 2025
Department of Surgery and Specialties, Faculty of Medicine and Pharmaceutical Sciences, University of Douala, Douala, Cameroon.
Objective: This study aimed to evaluate the efficacy and safety of bisphenol A-glycidyl methacrylate (bis-GMA) without UV light polymerization for the repair of refractory iatrogenic cerebrospinal fluid (CSF) leaks with large skull base defects.
Background: CSF leakage remains a common complication after neurosurgical interventions with a substantial resultant impact on morbidity and increased healthcare costs. The management of refractory CSF leaks with large skull base defects remains challenging.
Degradable thermosets via orthogonal polymerizations of a single monomer.
Nature
January 2025
Department of Chemistry and Chemical Biology, Cornell University, Ithaca, NY, USA.
Crosslinked thermosets are highly durable materials, but overcoming their petrochemical origins and inability to be recycled poses a grand challenge. Many strategies to access crosslinked polymers that are bioderived or degradable-by-design have been proposed, but they require several resource-intensive synthesis and purification steps and are not yet feasible alternatives to conventional consumer materials. Here we present a modular, one-pot synthesis of degradable thermosets from the commercially available, biosourced monomer 2,3-dihydrofuran (DHF).
View Article and Find Full Text PDFDynamic flow control through active matter programming language.
Nat Mater
January 2025
Division of Biology and Biological Engineering, California Institute of Technology, Pasadena, CA, USA.
Cells use 'active' energy-consuming motor and filament protein networks to control micrometre-scale transport and fluid flows. Biological active materials could be used in dynamically programmable devices that achieve spatial and temporal resolution that exceeds current microfluidic technologies. However, reconstituted motor-microtubule systems generate chaotic flows and cannot be directly harnessed for engineering applications.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!