The purpose of this investigation was to document the failure rate and length of service of crowns and fixed partial dentures (FPDs) fabricated in a Nigerian dental school. The reasons for failure of the initial restorations and their length of service were also ascertained. Also, the numbers of retainers, pontics, and the types of restoration were recorded. Poor esthetics was the most frequent cause of failure, 66 units (40.5%); followed by fracture, 58 units (35.6%); and dental caries, 25 units (15.4%). These outcomes were contrary to findings previously reported in studies from western countries where dental caries was principally responsible for failures (22.0% to 38.0% of cases). The resin-retained FPDs had the shortest mean years of service at 2.7 years, while the three-unit metal-ceramic FPDs had the greatest longevity at 8.6 years. The overall mean years of service for replaced restorations were 5.6 years. The study found a decrease in the mean years of service as the number of units in the fixed-fixed partial dentures increased. This is in sharp contrast to previous reports where no relationship existed between length of service and the number of units in a FPD.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
Evaluation of Retentive Forces in Three Types of Removable Partial Denture Framework Materials: An In Vitro Study.
Cureus
December 2024
Dentistry, Kurdistan Higher Council of Medical Specialties, Erbil, IRQ.
Introduction The utilization of Computer-Aided Design and Computer-Aided Manufacturing (CAD/CAM) technology in the production of polyetheretherketone (PEEK) and acetal frameworks enhances the precision and stability of partial denture frameworks. This study evaluates the retentive forces of CAD/CAM-fabricated PEEK, acetal, and cobalt-chromium (Co-Cr) frameworks in removable partial dentures (RPDs). Methods Forty-five frameworks were fabricated (15 each of PEEK, acetal, and Co-Cr) and tested for retentive forces using a universal testing machine at a crosshead speed of 5 mm/min.
View Article and Find Full Text PDFEffects of computer-assisted learning for removable partial denture design on learning outcomes and satisfaction.
BMC Med Educ
January 2025
Department of Prosthodontics, Faculty of Dentistry, Chiang Mai University, Chiang Mai, Thailand.
Background: Computer-assisted learning (CAL) has the potential to enhance learning outcomes and satisfaction. However, there are limited reports in the literature that describe or evaluate the implementation of this method to promote competency-based learning in removable partial denture (RPD) design. Therefore, this study aimed to: (1) compare the effectiveness of different learning methods using a 3D software-aided RPD design program, (2) evaluate the learning outcomes associated with these different methods following active learning, and (3) assess students' satisfaction.
View Article and Find Full Text PDFComparative In Vitro Analysis of Fracture Toughness and Flexural Strength in Interim Fixed Partial Dentures Reinforced With Various Nanofibers.
Cureus
December 2024
Prosthodontics and Crown and Bridge, The Oxford Dental College, Bengaluru, IND.
Aim To evaluate and compare the fracture toughness and flexural strength of interim fixed partial dentures reinforced with carbon, glass, and Kevlar nanofibers. Materials and methods This study explored the effect of reinforcing poly methyl methacrylate with carbon, glass, and Kevlar fibers on its fracture toughness and flexural strength. A total of 120 samples were prepared, divided into two groups of 60 samples each, with one group tested for fracture toughness and the other for flexural strength.
View Article and Find Full Text PDFEffect of Occlusal Scheme and Bone-Level Implant Number and Position on Stress Distribution in Kennedy Class II Implant-Assisted Removable Partial Dentures: A 3D Finite Element Analysis.
Clin Exp Dent Res
February 2025
Dental Research Center, Dentistry Research Institue and Department of Prosthodontics, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.
Objectives: To assess the effect of occlusion and implant number/position on stress distribution in Kennedy Class II implant-assisted removable partial denture (IARPD).
Materials And Methods: IARPDs were designed in six models: with one implant (bone level with a platform of 4 mm and length of 10 mm) at the site of (I) canine, (II) between first and second premolars, (III) first molar, (IV) second molar, or two implants at the sites of (V) canine-first molar, and (VI) canine-second molar. A conventional RPD served as control.
The influence of prosthetic treatments and implant-supported prostheses on posterior mandibular ridge atrophy: a retrospective cohort study.
BMC Oral Health
January 2025
Division of Restorative Dentistry, Periodontology and Prosthodontics, Department of Dental Medicine and Oral Health, Medical University of Graz, Billrothgasse 4, Graz, 8010, Austria.
Aims: Bone preservation is a requirement for long-term stability of dental prostheses, which is all the more important in the posterior mandible, given the particular challenges these areas pose to prosthetic treatment. The objective was to investigate the implications of different prostheses on the atrophy of posterior alveolar bone after tooth loss.
Materials And Methods: A total of 457 treatment cases were retrieved from the medical documentation and information network.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!