Characteristics of a new cermet X-ray tube for mammography are considered. The results of experimental testing of the tube are described.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
Impact of hBN Content on the Tribological Behavior and Thermal Diffusivity of HVOF-Sprayed CrC-NiCr Coatings.
Materials (Basel)
November 2024
Institute of Mechanical Engineering, Westphalian University of Applied Sciences, Neidenburgerstr. 43, 45897 Gelsenkirchen, Germany.
Considering the significant health risks posed by hard chrome plating during its application, thermally sprayed CrC-NiCr cermet coatings represent a suitable alternative. Incorporating hexagonal boron nitride (hBN) as a dry lubricant into the feedstock powder can further enhance wear resistance and thermal conductivity, crucial for preventing premature failure caused by inadequate lubrication. In this study, the mass fraction of hBN was varied between 0 and 15 wt.
View Article and Find Full Text PDFUnveiling Key Interface Characteristics of Ni/Yttria-Stabilized Zirconia Solid Oxide Cell Electrodes in HO Electroreduction Using Operando X-ray Photoelectron Spectroscopy.
ACS Appl Mater Interfaces
July 2024
Institut de Chimie et Procédés pour l'Energie, l'Environnement et la Santé (ICPEES), ECPM, UMR 7515 CNRS-Université de Strasbourg, 25 Rue Becquerel, 67087 Strasbourg Cedex 02, France.
Nickel/yttria-stabilized zirconia (YSZ) composites are the most commonly used fuel electrodes for solid oxide cells. While microstructural changes of Ni/YSZ during operational conditions have been thoroughly investigated, there is limited knowledge regarding Ni/YSZ surface chemistry under working conditions. In this study, we examine the interaction between Ni/YSZ electrodes and water vapor under open circuit and polarization conditions, utilizing near ambient pressure soft and hard X-ray photoelectron spectroscopies.
View Article and Find Full Text PDFCoZr nanocomposites in a ceramic-metal AlO(OH)/Al matrix with a different Co/Zr ratio and its potential for syngas processing.
Dalton Trans
June 2024
Federal Research Center Boreskov Institute of Catalysis SB RAS, Akad. Lavrentieva ave. 5, Novosibirsk 630090, Russia.
We investigated the possibility of synthesizing Co nanoparticles in CoZrH/AlO(OH)/Al ceramic-metal catalysts and controlling the catalytic properties of these nanoparticles in syngas conversion by changing the Co/Zr ratio. The CoZr nanocomposites were obtained from metal powders by mechanochemical activation in a high-energy mill under an argon atmosphere, followed by treatment with hydrogen at high pressure and room temperature. Ceramic-metal catalysts were prepared by mixing the corresponding CoZrH powder nanocomposite (30 wt%) with powdered aluminum (70 wt%), hydrothermal treatment of the mixture and subsequent calcination.
View Article and Find Full Text PDFPreparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets.
Materials (Basel)
April 2024
Fujian Province Key Laboratory of Functional Materials and Applications, Xiamen University of Technology, Xiamen 361024, China.
The use of metal-coated ceramic powders not only effectively enhances the wettability of the metal-ceramic interface but also promotes a more uniform microstructure in Ti(C,N)-based cermets, which is advantageous for improving their mechanical properties. In this study, ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders were synthesized via the spray-drying-in-situ carbothermal reduction method. Subsequently, Ti(C,N)-based cermets were effectively fabricated using the as-prepared ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders.
View Article and Find Full Text PDFCorrecting Hardening Artifacts of Aero-Engine Blades with an Iterative Linear Fitting Technique Framework.
Sensors (Basel)
March 2024
School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China.
Aero engines are the key power source for aerospace vehicles. Cermet turbine blades are the guarantee for the new-generation fighters to improve aero-engine overall performance. X-ray non-destructive reconstruction can obtain the internal structure and morphology of cermet turbine blades.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!