Resonant vibration investigations for piezoceramic disks and annuli by using the equivalent constant method.

IEEE Trans Ultrason Ferroelectr Freq Control

Department of Mechanical Engineering, Ching Yun University, Chung-Li, Taiwan.

Published: August 2005

This paper presents the equivalent constant method to investigate the transverse vibration of piezoceramic disks and annuli. By comparing the characteristic equations of resonant frequencies between isotropic and piezoceramic disks, the named equivalent Poisson's ratio v is derived, then the transverse vibration characteristic equation can be expressed as a single formulation for these two materials. To verify this method, characteristic equations of transverse vibration for piezoceramic disks and annuli with many different boundary conditions are discussed and calculated for resonant frequencies. Numerical calculations based on the finite-element method (FEM) also are performed, and the results agree rather well with the theoretical predictions. With the aid of the relations between frequency parameter and equivalent Poisson's ratio in explicit form, the other application of equivalent Poisson's ratio is the inverse evaluation of material constants. The laser Doppler vibrometer (LDV) and impedance analyzer are used to experimentally obtain the resonant frequencies of transverse and radial extensional vibrations, respectively. By the experimental results for the traction-free piezoceramic disk, the planar Poisson's ratio v(p) and planar electromechanical coupling coefficient k(p) are determined.

Download full-text PDF

Source
http://dx.doi.org/10.1109/tuffc.2005.1509780DOI Listing

Publication Analysis

Top Keywords

piezoceramic disks
16
poisson's ratio
16
disks annuli
12
transverse vibration
12
resonant frequencies
12
equivalent poisson's
12
equivalent constant
8
constant method
8
vibration piezoceramic
8
characteristic equations
8

Similar Publications

The performance of ultrasonic transducers is largely determined by the piezoelectric properties and geometries of their active elements. Due to the brittle nature of piezoceramics, existing processing tools for piezoelectric elements only achieve simple geometries, including flat disks, cylinders, cubes and rings. While advances in additive manufacturing give rise to free-form fabrication of piezoceramics, the resultant transducers suffer from high porosity, weak piezoelectric responses, and limited geometrical flexibility.

View Article and Find Full Text PDF

Cyclic Mechanical Fatigue Lifetime of BiNaTiO-Based Eco-Piezoceramics.

Materials (Basel)

July 2021

Instituto de Ciencia de Materiales de Madrid, CSIC, 28049 Madrid, Spain.

The mechanical strength and cyclic fatigue behavior of PIC700 commercial eco-piezoceramic disks are investigated under biaxial loading on unpoled and poled samples. The bending strength of unpoled samples was higher than those of poled ones. Fatigue tests were conducted under a load ratio of 10 at a frequency of 20 Hz with a sinusoidal waveform.

View Article and Find Full Text PDF

Tonpilz transducers are desirable for their superior performance in underwater target detection and communication applications. Several design schemes to widen their bandwidth have been reported, but these schemes often involve a complex structure or arrangement of additional components. In this study, a simple design is proposed to improve the bandwidth of a multimode Tonpilz transducer by using a non-uniform drive section that consists of piezoelectric stacks of various thicknesses.

View Article and Find Full Text PDF

Rayleigh Wave Calibration of Acoustic Emission Sensors and Ultrasonic Transducers.

Sensors (Basel)

July 2019

Department of Materials Science and Engineering, University of California, Los Angeles (UCLA), Los Angeles, CA 90095, USA.

Acoustic emission (AE) sensors and ultrasonic transducers were characterized for the detection of Rayleigh waves (RW). Small aperture reference sensors were characterized first using the fracture of glass capillary tubes in combination with a theoretical displacement calculation, which utilized finite element method (FEM) and was verified by laser interferometer. For the calibration of 18 commercial sensors and two piezoceramic disks, a 90° angle beam transducer was used to generate RW pulses on an aluminum transfer block.

View Article and Find Full Text PDF

Concrete-filled square steel tube column (CFSSTC) joints are the most important parts of concrete-filled steel tube frame structures. It is of great significance to study the damage of CFSSTC joints under the seismic loads. In this paper, embedded piezoceramic transducers are used to monitor the damage of core concrete of CFSSTC joints under cyclic loading and surface-bonded piezoceramic disks are used to monitor the debonding damage of the steel tube and core concrete of two specimens.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!