The utilization of polychaetes in descriptive ecology is reviewed in the light of recent research especially concerning the biota hard bottom environments. Polychaetes, often linked in the past to the concept of opportunistic species able to proliferate after an increase in organic matter, have played an important role especially with regard to impacted soft-bottom habitats. Increased knowledge of the group, suggests that not only opportunistic species can be utilised as indicators, so that these organisms can be disengaged from the old concept of opportunistic taxa. Moreover, recent researches conducted on this group allowed demonstrating as surrogacy is not always applicable. Among polychaetes inhabiting hard bottom environment, the analysis of family Syllidae appears particularly promising. Studied conducted in our laboratory demonstrated as syllid species decrease in abundance or completely disappear under varying sources of negative impact. The distribution of species also appeared indicative in underlying effects of marine protected areas (MPA) functioning, or in describing different climatic areas within biogeographical sectors. It is obvious that good results can only be obtained on the basis of good taxonomic resolution. We suggested that, in monitoring studies, operational time could be optimized not only by working at a higher-level on the whole invertebrate data set, but by also selecting a particularly indicative group and working at fine level.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.marpolbul.2005.08.003 | DOI Listing |
Nanomaterials (Basel)
December 2024
School of Mechanical and Electrical Engineering, Soochow University, Suzhou 215137, China.
Composite coatings reinforced with varying mass fractions of SiC particles were successfully fabricated on 316 stainless steel substrates via laser cladding. The phase compositions, elemental distribution, microstructural characteristics, hardness, wear resistance and corrosion resistance of the composite coatings were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Vickers hardness testing, friction-wear testing and electrochemical methods. The coatings have no obvious pores, cracks or other defects.
View Article and Find Full Text PDFPharmaceuticals (Basel)
December 2024
College of Science and Engineering, Flinders University, Bedford Park, South Australia 5042, Australia.
Two fibre optic probes were custom designed to perform Raman and near-infrared spectroscopic measurements. Our long-term objective is to develop a non-destructive tool able to collect data in hard-to-access locations for real-time analysis or diagnostic purposes. This study evaluated the quantitative performances of Probe A and Probe B using model pharmaceutical tablets.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
Department Dental Clinical Sciences, Dalhousie University, 5981 University Avenue, Halifax, NS B3H 4R2, Canada.
The load and size of the indentation may affect the hardness value. This study investigated the effect of the indentation size on the microhardness of one resin-based composite (RBC). Metal molds 4 mm deep and 12 mm in diameter were filled with Tetric EvoCeram Bulk Fill (Ivoclar) and light-cured for 10 s using a broad-spectrum LED curing light.
View Article and Find Full Text PDFAnimals (Basel)
December 2024
Centro de Estudos de Ciência Animal (CECA), Instituto de Ciências, Tecnologias e Agroambiente da Universidade do Porto (ICETA), Rua D. Manuel II, Apartado 55142, 4051-401 Porto, Portugal.
The aim of this preliminary study was to morphologically and dimensionally characterize the cat's olfactory bulb in the sagittal plane and to establish potential relationships with the cranial conformation, based on the study of in vivo MRI images. Midsagittal and transverse T2-weighted images of the head of 40 cats subjected to MRI were selected. For each animal, the skull index was calculated to classify the cranial conformation.
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
Functional Nanomaterials Laboratory, Center for Micro/Nanomaterials and Technology, and Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190, China.
Antireflection (AR) coatings with mechanical robustness and superhydrophobic properties have wide potential applications in optical, electronic, and automotive fields. However, the fabrication of large-sized, robust, and multifunctional AR coatings on plastic/polymer substrates has been a challenging problem. In this study, we developed a bottom-up approach to produce mechanically robust, enhanced transmittance, and superhydrophobic coatings on poly(methyl methacrylate) (PMMA) substrate.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!