Viscous fingering is a flow instability phenomenon that results in the destabilisation of the interface between two fluids of differing viscosities. The destabilised interface results in a complex mixing of the two fluids in a pattern that resembles fingers. The conditions that enhance this type of flow instability can be found in coupled chromatographic separation systems, even when the solvents used in each of the separation stages have seemingly similar chemical and physical properties (other than viscosity). For example, the viscosities of acetonitrile and methanol are sufficiently different that instability at the interface between these two solvents can be established and viscous fingering results. In coupled chromatographic systems, the volume of solvent transported from one separation dimension to the second often exceeds the injection volume by two or more orders of magnitude. As a consequence, viscous fingering may occur, when otherwise following the injection of normal analytical size injection plugs viscous fingering would not occur. The findings in this study illustrate the onset of viscous fingering in emulated coupled chromatographic systems and show the importance of correct solvent selection for optimum separation performance.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.chroma.2005.04.093DOI Listing

Publication Analysis

Top Keywords

viscous fingering
24
flow instability
12
coupled chromatographic
12
chromatographic systems
8
fingering occur
8
viscous
6
fingering
5
fingering induced
4
induced flow
4
instability
4

Similar Publications

Hypothesis: Viscous fingering instabilities of air displacing water displacing mineral oil is controlled by the air injection rate. Given the lower viscosity of the water, air would tend to finger through the water and then after it reaches the oil, proceed to finger through the oil.

Experiments: In a radial Hele-Shaw cell, experiments were conducted on air injection into mineral oil and air injection into a volume of water at the center of the cell which in turn is surrounded by mineral oil.

View Article and Find Full Text PDF

Supercritical CO, as an environmentally friendly and pollution-free fluid, has been applied in various EOR techniques such as CO flooding. However, the low viscosity of the gas leads to issues such as early breakthrough, viscous fingering, and gravity override in practical applications. Although effective mobility-control methods, such as CO WAG (water alternating gas)-, CO foam-, and gel-based methods, have been developed to mitigate these phenomena, they do not fundamentally solve the problem of the high gas-oil mobility ratio, which leads to reduced gas sweep efficiency.

View Article and Find Full Text PDF

Fluid displacement within layered porous media is more complex than in nonlayered ones. Most of the previous studies placed a focus on the porous media with layerings perpendicular to the flow direction, and the effects of pore topology were often ignored. Therefore, this study aims to reveal the flow physics in porous media with layering parallel to the flow direction by accounting for the specific pore topology.

View Article and Find Full Text PDF

Polymer solution injection has emerged as a promising method for the remediation of NAPL (non-aqueous phase liquids)-contaminated aquifers. This technique enhances recovery efficiency by modifying viscous forces, stabilizing the displacement front, and minimizing channeling effects. However, there remains a significant gap in understanding the behavior of polymer solutions, particularly those with different molecular weights (MW), for mobilizing DNAPL (dense non-aqueous phase liquids) trapped in heterogeneous aquifers, especially within low-permeability layers.

View Article and Find Full Text PDF

Flow-driven pattern formation during coacervation of xanthan gum with a cationic surfactant.

Phys Chem Chem Phys

December 2024

Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstr. 400, 01328 Dresden, Germany.

We experimentally demonstrate that the coacervation of a biopolymer can trigger a hydrodynamic instability when a coacervate is formed upon injection of a xanthan gum dispersion into a cationic surfactant (CTAB) solution. The local increase of the viscosity due to the coacervate formation induces a viscous fingering instability. Three characteristic displacement regimes were observed: a viscous fingering dominated regime, a buoyancy-controlled "volcano" regime and a "fan"-like regime determined by the coacervate membrane dynamics.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!