This study investigated intra- and inter-rater reliability of several radiographic angular and linear parameters using 6 subjects. Using standard weight-bearing radiographs, the following measurements were performed: first metatarsal protrusion distance, hallux abductus, first intermetatarsal, calcaneal inclination and lateral intermetatarsal angles. Measurement of lateral stressed dorsiflexion of the first metatarsophalangeal joint and the rearfoot-to-forefoot-axis angle taken using a composite view were also obtained. All parameters were measured independently by 2 raters, and measurements were repeated on 3 separate occasions at weekly intervals. Intrarater reliability of radiographic measurements ranged between R = 0.65-1.00 for lateral stressed dorsiflexion, and between R = 0.91 and 0.99 for the rearfoot to forefoot axis angle. Inter-rater reliability of radiographic measurements ranged from R = 0.82-0.99. Specifically, lateral stressed dorsiflexion showed R = 0.87 with a mean difference of -1.47 (confidence interval [CI]: -3.42, 0.47), indicating no significant difference ( t = 1.54, P = 0.13). The rearfoot-to-forefoot-axis angle showed R = 0.92 with a mean difference of -0.15 (CI: -1.05, 0.74), indicating no significant difference ( t = 0.35, P = 0.73). The 7 angular and linear measurements chosen demonstrated high inter- and intrarater reliability. These results indicate that weight-bearing radiographic first metatarsophalangeal joint dorsiflexion using the lateral stressed dorsiflexion view, and measurement of the rearfoot-to-forefoot-axis angle using a composite view could be measured reliably within and between raters.

Download full-text PDF

Source
http://dx.doi.org/10.1053/j.jfas.2005.02.011DOI Listing

Publication Analysis

Top Keywords

lateral stressed
16
stressed dorsiflexion
16
angular linear
12
metatarsophalangeal joint
12
reliability radiographic
12
rearfoot-to-forefoot-axis angle
12
linear measurements
8
joint dorsiflexion
8
rearfoot forefoot
8
forefoot axis
8

Similar Publications

Effects of Different Humeral Stem Length on Stem Alignment and Proximal Stress Shielding in Reverse Total Shoulder Arthroplasty.

J Shoulder Elbow Surg

January 2025

Department of Orthopaedic Surgery, Seoul National University College of Medicine, Seoul National University Bundang Hospital, Seongnam, Republic of Korea. Electronic address:

Background: Few comparative studies on the correlation between stem length, stem alignment, and/or stress shielding have been conducted in reverse total shoulder arthroplasty (rTSA). This study aimed to investigate the effects of different humeral stem lengths on stem alignment and proximal stress shielding after rTSA.

Methods: A total of 320 patients who underwent primary rTSA from October 2010 to May 2020 with at least 2 years of follow-up (mean follow-up: 32.

View Article and Find Full Text PDF

Roots play essential roles in the acquisition of water and minerals from soils in higher plants. However, water or nutrient limitation can alter plant root morphology. To clarify the spatial distribution characteristics of essential nutrients in citrus roots and the influence mechanism of micronutrient deficiency on citrus root morphology and architecture, especially the effects on lateral root (LR) growth and development, two commonly used citrus rootstocks, trifoliate orange ( L.

View Article and Find Full Text PDF

: This study aimed to compare the effects of surgically assisted rapid palatal expansion (SARPE) techniques and their combinations on the stresses (von Mises, maximum principal, and minimum principal) and displacements that occur in the maxilla, facial bones, and maxillary teeth using three-dimensional finite element analysis (FEA). : SARPE was simulated using seven different osteotomy techniques. The FEA models were simulated with a combination of various osteotomies, including midpalatal and lateral osteotomies, lateral osteotomy with a step, and separation of the pterygomaxillary junction.

View Article and Find Full Text PDF

Mechanoluminescent (ML) materials emit light by trapping and releasing charge carriers under mechanical stress. However, previous studies do not fully reveal the relationship between emitting light intensity and mechanical stress, thereby affecting the accuracy of stress measurement. This study addresses this gap by systematically investigating ML cylinders with various sizes and loading paths using theoretical analysis and simulations, focusing on the maximum contact stress, equivalent stress distribution, and the relationship between the strain energy density and light intensity at the point of maximum contact stress.

View Article and Find Full Text PDF

Welding-induced residual stress has the capacity to significantly compromise the integrity of mechanical components. Its minimization therefore plays a critical role in the selection of process parameters during the welding process. Friction stir welding is a useful joining technique to weld many materials that are not amenable to the traditional welding techniques.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!