Objective: To describe architectural changes along the dorsal laminar interface of the equine foot.
Sample Population: 6 macroscopically normal forefeet obtained from 6 equine cadavers.
Procedure: Histologic sections of 8 evenly spaced, proximal to distal, samples of the dorsal laminar interface were photographed, digitized, and examined for differences in architecture. Laminar depth; secondary laminar density; number and consistency of bifurcations occurring within the secondary laminae, and areas composed of primary dermal lamina, primary epidermal lamina, and secondary laminar interface were recorded. Data were examined to test for differences in architecture associated with the proximal to distal positioning of the sample.
Results: With exception of the areas of the primary epidermal and primary dermal lamina, all measured variables were significantly different between the proximal and distal regions of the dorsal laminar interface. Changes included increases in laminar depth and the secondary laminar density. Bifurcation of secondary laminae principally occurred proximally and had an increased depth of bifurcation distally. The secondary laminar dermal-epidermal interface had a 109% increase in area between the most proximal and distal sections.
Conclusions And Clinical Relevance: Results of this study indicate that the interface normally contributes a substantial volume of dermal components to the internal surface of the wall. These data also indicate that 2 distinct mechanisms (i.e., bifurcation of secondary laminae and an increase in the length of secondary laminae) contribute to changes in the architecture of the laminar interface, which allows for the hypothesis that the normal laminar interface is capable of responding to mechanical load.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.2460/ajvr.2005.66.277 | DOI Listing |
Sci Total Environ
December 2024
Institute of Experimental Medicine of the Czech Academy of Sciences, Videnska 1084, Prague 4, Czech Republic.
Exposure of cell cultures at air-liquid interface (ALI), mimicking i.e. human lung surface, is believed to be one of the most realistic means to model toxicity of complex mixtures of pollutants on human health.
View Article and Find Full Text PDFProc Natl Acad Sci U S A
December 2024
Department of Earth and Environmental Sciences, College of Science and Engineering, University of Minnesota, Minneapolis, MN 55455.
Solute transport and biogeochemical reactions in porous and fractured media flows are controlled by mixing, as are subsurface engineering operations such as contaminant remediation, geothermal energy production, and carbon sequestration. Porous media flows are generally regarded as slow, so the effects of fluid inertia on mixing and reaction are typically ignored. Here, we demonstrate through microfluidic experiments and numerical simulations of mixing-induced reaction that inertial recirculating flows readily emerge in laminar porous media flows and dramatically alter mixing and reaction dynamics.
View Article and Find Full Text PDFJ Chromatogr A
November 2024
Institute of Functional Interfaces, Karlsruhe Institute of Technology, 76344 Eggenstein-Leopoldshafen, Germany. Electronic address:
Recently, the focus in chromatography model development has expanded to include the modeling of extra column volume (ECV), particularly in small- and lab-scale systems where ECV can constitute a significant portion of the total volume. Typically, ECV is modeled with 1D approaches, for example with combinations of dispersed plug flow reactors (DPFRs) and continuously stirred tank reactors (CSTRs). However, radial inhomogeneities in the ECV concentration profile necessitate higher-dimensional models for more accurate predictions.
View Article and Find Full Text PDFACS Appl Mater Interfaces
December 2024
The Key Laboratory of Synthetic and Biological Colloids, Ministry of Education, School of Chemical and Material Engineering, International Joint Research Laboratory for Nano Energy Composites, Jiangnan University, Wuxi, Jiangsu 214122, P.R. China.
Graphene oxide (GO) is widely used to prepare 2D laminar separation membranes because of its single atomic thickness and good processability. However, due to the tortuous transport path and excessive swelling effect, it is difficult to improve permeability, salt rejection, and stability of GO membranes simultaneously. Herein, we chemically laminated GO with covalent organic framework nanosheets (CONs) to fabricate membranes for fast and stable desalination.
View Article and Find Full Text PDFACS Appl Mater Interfaces
November 2024
Zhejiang Provincial Engineering Center of Integrated Manufacturing Technology and Intelligent Equipment, Hangzhou City University, Hangzhou 310015, China.
A strategy for fabrication of macroporous hydrogels through 3D printing assisted by molding and multiple microfluidic bubble-templating nozzles is proposed here. This approach aims to address the challenges faced by methods for 3D printing macroporous hydrogels, such as difficulties in precisely controlling the spatial distribution of macropores, limited porosity, and low resolution of external boundaries due to the poor mechanical properties of hydrogel solutions as printing ink. In this method, fast-switching microfluidic bubble-templating nozzles of varying sizes allowed for precise control of target pore sizes over a wide range.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!