This paper reports on the preparation of polyester brushes at the surface of electrically conducting materials. A two-step strategy has been worked out that consists of the electropolymerization of an acrylate under a cathodic potential, such that the polyacrylate layer is chemisorbed at the surface. In a second step, either preformed poly(epsilon-caprolactone) chains are grafted onto the polyacrylate sublayer or the ring-opening polymerization of epsilon-caprolactone is initiated from it.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/la048357u | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Designing Hybrid Plasmonic Superlattices with Spatially Confined Responsive Heterostructural Units.
Nano Lett
January 2025
State Key Laboratory of Solidification Processing, Center of Advanced Lubrication and Seal Materials, School of Materials Science and Engineering, Northwestern Polytechnical University, Xi'an 710072, P.R. China.
Plasmonic superlattices enable the precise manipulation of electromagnetic fields at the nanoscale. However, the optical properties of static lattices are dictated by their geometry and cannot be reconfigured. Here, we present a surface-interface engineered plasmonic superlattice with confined polyelectrolyte-functionalized metal-organic framework (MOF) hybrid layers to tune plasmon resonance for ultrafast chemical sensing.
View Article and Find Full Text PDFConstruction of Loop Polyzwitterion Brushes on PET Sheets via the Chain-End Closure Strategy To Improve Antifouling and Hemocompatible Properties.
Langmuir
January 2025
Jiangsu Collaborative Innovation Center of Biomedical Functional Materials, Jiangsu Key Laboratory of Bio-functional Materials, Department of Materials Science and Engineering, School of Chemistry and Materials Science, Nanjing Normal University, Nanjing 210023, P. R. China.
Steric stabilization and lubrication give loop polymer brushes enhanced antifouling properties. In the study, linear zwitterionic poly(NMASMCMS) brushes were first constructed on a poly(ethylene terephthalate) (PET) surface through surface-initiated reversible addition-fragmentation chain-transfer (SI-RAFT) polymerization. The tethered linear brushes on sheets were then thiolated with ethanolamine, followed by oxidation to form loop brushes.
View Article and Find Full Text PDFSuperhydrophilic PVDF membrane fabricated on modified TiO/CS-SDAEM nanoparticles deposited on GA/CNTs hydrophilic layer to achieve self-cleaning photodegradation and low contamination rate for dyestuff separation.
Int J Biol Macromol
December 2024
Department of Automotive Engineering, Jining Polytechnic, Jining 272103, China.
In this work CS-SDAEM polymer brushes with long-chain structure were synthesized, and TiO/CS-SDAEM nanoparticles were prepared by modifying them on the TiO surface. The prepared modified membrane can effectively degrade dyes through photocatalysis and can reduce the contamination rate of the membrane during use. The separation membrane achieves efficient removal of contamination by self-cleaning.
View Article and Find Full Text PDFRelative abrasive potential of silica-based conventional and tablet dentifrices on enamel and dentin.
PLoS One
December 2024
Department of Restorative and Reconstructive Oral Care, Academic Centre for Dentistry Amsterdam (ACTA), Universiteit van Amsterdam and Vrije Universiteit Amsterdam, Amsterdam, The Netherlands.
Objectives: This in vitro study aimed to investigate the toothbrushing wear on both enamel and dentin surfaces of reference and commercially available dentifrices.
Methods: Bovine enamel and dentin blocks were initially polished and embedded within a resin composite in square shapes (10×8×6 mm3). Employing toothbrushes equipped with nylon bristles, a toothbrushing machine was utilized, subjecting dentin specimens (n = 36) to 500 brush cycles and enamel samples to 5000 brush cycles (n = 36).
The Effects of Different Hygiene Instrumentations on Titanium Implant Fixture Surfaces.
Cureus
November 2024
School of Dental Sciences, Universiti Sains Malaysia, Kota Bharu, MYS.
Background and objective Applying different hygiene tools for implant maintenance alters surface configurations, impacting bacterial adhesion on titanium implant surfaces and potentially leading to peri-implant diseases. This study aimed to assess the alterations in surface topography of titanium implant fixtures after utilizing hygiene instruments such as airflow; erbium, chromium-doped: yttrium, scandium, gallium, and garnet (Er, Cr: YSGG) laser; and titanium brush, under scanning electron microscope (SEM) observation. Materials and methods We employed an experimental laboratory study design for this research, involving 20 MegaGen ST titanium implant fixtures (MegaGen Implant Co.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!