Comparative investigation of the biocompatibility of various silicon nitride ceramic qualities in vitro.

J Mater Sci Mater Med

Department of Otorhinolaryngology, University of Essen, Hufelandstr. 55, 45122 Essen, Germany.

Published: October 2004

There is a controversy about the biocompatibility of silicon nitride ceramics contained in the literature, which appears to be related to a factor of the individual chemical composition of different qualities of silicon nitride ceramics and of the different surface properties. This study attempts to investigate the cytotoxicity of different qualities of industrial silicon nitride ceramics applying an L929-cell culture model in a direct contact assay combined with a cell viability assessment. Five different qualities of industrial standard silicon nitride ceramics were chosen for in vitro testing. The chemical composition was determined by EDS analysis. Different biomedically approved aluminium oxide qualities, a titanium alloy, glass and polyvinylchloride (PVC) served as control materials. L929 mice fibroblasts were incubated directly on the materials for 24 h, stained with bisbenzimide and propidium iodine for double fluorochromasia viability testing, and evaluated by inversion-fluorescence microscopy to control cell morphology, viability and cell counts compared to empty well values. Scanning electron microscopy was applied to additionally investigate cell morphology. There was no observation of cytotoxic effects on the silicon nitride ceramic samples; moreover cell morphology remained the same as on aluminium oxide and titanium. Viability testing revealed the presence of avital cells exclusively on PVC, which served as a negative control. Cell counts on all polished surfaces showed significantly higher numbers, whereas some rough surface samples showed significantly lower numbers. We conclude that silicon nitride ceramics show no cytotoxic effects and should be considered for biomedical application owing to its favourable physiochemical properties, especially its superior resistance to mechanical stress, which would be useful for compression loaded conditions. Polished surfaces would appear to promote advanced biocompatibility.

Download full-text PDF

Source
http://dx.doi.org/10.1023/B:JMSM.0000046396.14073.92DOI Listing

Publication Analysis

Top Keywords

silicon nitride
28
nitride ceramics
20
cell morphology
12
biocompatibility silicon
8
nitride ceramic
8
chemical composition
8
qualities industrial
8
aluminium oxide
8
pvc served
8
viability testing
8

Similar Publications

We experimentally demonstrate what we believe to be a novel RF interference mitigation technique using a network of low-loss silicon nitride ring resonators. The rings are used for complex (phase and amplitude) line-by-line shaping of higher-order sidebands from an electro-optic modulator to discriminate large and small RF signal input, thereby achieving strong (30 dB) mitigation of a large signal and virtually no mitigation for small signals.

View Article and Find Full Text PDF

In this paper, we quantitatively compare the autofluorescence of stoichiometric low pressure chemical vapor deposition (LPCVD) silicon nitride and sputtered tantalum pentoxide waveguides at a pump wavelength of 532 nm. Through a direct quantitative characterization of comparable waveguides formed from the two films, we find no observable autofluorescence for tantalum pentoxide waveguides. Our experimental sensitivity is limited by Raman scattering of the pump into our detection band and our measurements indicate that the autofluorescence of the tantalum pentoxide waveguides is more than 600 × smaller than that of silicon nitride waveguides.

View Article and Find Full Text PDF

Silicon nitride (SiN) integrated photonics is a highly promising platform for photonic quantum information processing. However, the efficient generation of single photons remains a significant challenge. Epitaxial InAs/GaAs quantum dots (QDs) embedded in wavelength-scale nanocavities offer a promising solution as single-photon sources (SPSs), but their integration with SiN has not yet been demonstrated.

View Article and Find Full Text PDF

Localized Nanopore Fabrication in Silicon Nitride Membranes by Femtosecond Laser Exposure and Subsequent Controlled Breakdown.

ACS Appl Mater Interfaces

January 2025

Division of Micro and Nanosystems (MST), School of Electrical Engineering and Computer Science (EECS), KTH Royal Institute of Technology, Stockholm SE-10044, Sweden.

Controlled breakdown has emerged as an effective method for fabricating solid-state nanopores in thin suspended dielectric membranes for various biomolecular sensing applications. On an unpatterned membrane, the site of nanopore formation by controlled breakdown is random. Nanopore formation on a specific site on the membrane has previously been realized using local thinning of the membrane by lithographic processes or laser-assisted photothermal etching under immersion in an aqueous salt solution.

View Article and Find Full Text PDF

Scale-Up of Nanocorundum Synthesis by Mechanochemical Dehydration of Boehmite.

Ind Eng Chem Res

January 2025

Max-Planck-Institut für Kohlenforschung, Kaiser-Wilhelm-Platz 1, D-45470 Mülheim an der Ruhr, Germany.

This work presents the scale-up of room-temperature mechanochemical synthesis of nanocorundum (high-surface-area α-AlO) from boehmite (γ-AlOOH). This transformation on the 1 g scale using a laboratory shaker mill had previously been reported. High-energy Simoloyer ball mills equipped with milling chambers of sizes ranging from 1 to 20 L were used to scale up the mechanochemical nanocorundum synthesis to the 50 g to 1 kg scale, which paves the way to further increase batch size.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!