Surface smoothness is one of the properties determining the performance of stents. Therefore, surface polishing shows its importance in the exploitation and production of stents. The present study explores electrochemical polishing of 316L stainless steel slotted tube coronary stents produced by laser cutting. Acid pickling was also studied as a pre-treatment of electrochemical polishing of the stents to remove the slag (oxides) formed in the production of the stents. Meanwhile, removal of the material was measured as well, caused by both acid pickling and electrochemical polishing processes. It is found that the slag formed on the surface of stents due to the laser cutting production process could be removed by means of acid pickling. Electrochemical polishing results in a smooth stent surface. Meanwhile, both acid pickling and electrochemical polishing applied in the present study have a proper removal of the stent material.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1023/a:1019831808503 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
A Molecularly Imprinted Electrochemical Sensor for Carbendazim Detection Based on Synergy Amplified Effect of Bioelectrocatalysis and Nanocomposites.
Polymers (Basel)
January 2025
Key Laboratory of Radiopharmaceuticals, Ministry of Education, College of Chemistry, Beijing Normal University, Beijing 100875, China.
The highly selective and sensitive determination of pesticide residues in food is critical for human health protection. Herein, the specific selectivity of molecularly imprinted polymers (MIPs) was proposed to construct an electrochemical sensor for the detection of carbendazim (CBD), one of the famous broad-spectrum fungicides, by combining with the synergistic effect of bioelectrocatalysis and nanocomposites. Gold nanoparticle-reduced graphene oxide (AuNP-rGO) composites were electrodeposited on a polished glassy carbon electrode (GCE).
View Article and Find Full Text PDFFlexible disk ultramicroelectrode: Facile preparation and high-resolution scanning electrochemical microscopy imaging.
Anal Chim Acta
January 2025
State Key Laboratory of Electroanalytical Chemistry, Jilin Province Key Laboratory of Low Carbon Chemical Power, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun, 130022, Jilin, China; School of Applied Chemistry and Engineering, University of Science and Technology of China, Hefei, 230026, Anhui, China. Electronic address:
Background: Scanning electrochemical microscopy (SECM) is a kind of scanning probe technology that enables the obtainment of surface morphology and electrochemical information by recording changes in Faraday current triggered by the movement of probe.
Results: In this work, flexible disk ultramicroelectrode (UME) with highly repeatable geometry are fabricated through a simple and universal strategy that involves vacuum pulling the glass capillaries inserted with platinum wire (gold wire, carbon fiber, etc.), followed by a rapidly heated sealing and polishing process.
Additively manufactured ready-to-use platform using conductive recycled PLA for ketamine sensing.
Mikrochim Acta
January 2025
Federal University of Uberlândia, Chemistry Institute, Uberlândia, MG, 38400-902, Brazil.
The use of 3D-printed electrodes is reported fabricated from in-house conductive filament composed of a mixture of recycled poly (lactic acid) (rPLA), graphite (Gpt), and carbon black (CB) for fast detection of the abused drug ketamine. Firstly, the performance of these electrodes was evaluated in comparison to 3D-printed electrodes produced employing a commercially available conductive filament. After a simple pretreatment step (mechanical polishing), the new 3D-printed electrodes presented better performance than the electrodes produced from commercial filament in relation to peak-to-peak separation of the redox probe [Fe(CN)]/ (130 mV and 759 mV, respectively), charge transfer resistance (R = 1.
View Article and Find Full Text PDFEvaluation of Treatment Effect and Mechanism Analysis of Ti6AL4V Porous Scaffolds Prepared by Selective Laser Melting with Different Chemical Polishing Processes.
3D Print Addit Manuf
October 2024
School of Electronics and Information Engineering, Guangdong Ocean University, Zhanjiang, China.
The large amount of unfused powder that remains on the surface of Ti6AL4V porous scaffolds prepared by selective laser melting technology is a common problem. Therefore, this article investigated the effects of three different chemical polishing processes on the surface state, pore structure, and mechanical properties of small pore size scaffold materials at different polishing times in the field of implantable medical devices. The results show that the overall treatment effect of the simple chemical polishing process is poor, the internal treatment depth of porous support is insufficient and uneven, and the overall mechanical properties of the sample with the same porosity are average.
View Article and Find Full Text PDFBio-based plasticizer Babassu oil for custom-made conductive additive-manufacturing filaments: towards 3D-printed electrodes applied to cocaine detection.
Mikrochim Acta
December 2024
Chemistry Institute, Federal University of Uberlândia, Uberlândia, MG, 38408-100, Brazil.
Babassu (Atallea sp.), a native palm tree from South America's Amazon produces bio-oil and biochar with significant potential for industrial applications. Babassu oil as a bio-based plasticizer is reported here for the first time to replace petrochemical alternatives in the production of conductive filaments for additive manufacturing purposes.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!