Radiant emissions from short, medium, and long wavelength thermal radiant emitter systems typically used for food processing applications were quantified. Measurements included heat flux intensity, emitter surface temperature, and spectral wavelength distribution. Heat flux measurements were found highly dependent on the incident angle and the distance from the emitter facing. The maximum flux measured was 5.4 W/cm2. Emitter surface temperature measurements showed that short wavelength radiant systems had the highest surface temperature and greatest thermal efficiency. The emitter spectral distributions showed that radiant emitter systems had large amounts of far infrared energy emission greater than 3 microm when compared to theoretical blackbody curves. The longer wavelength energy would likely cause increased surface heating for most high moisture content food materials.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1080/08327823.2003.11688500 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Low-Temperature Chemical Solution Deposition of BiOSe on Amorphous Surface for Dynamic Memristor of Physical Reservoir Array.
ACS Nano
January 2025
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Korea.
Bismuth oxyselenide (BiOSe) stands as a highly promising layered semiconductor with outstanding optical, electrical, and thermal properties. For the practical application of the material toward the devices, growing BiOSe directly on the amorphous substrate at low temperatures (<400 °C) is essential; however, the negatively charged bottom Se layer originating from alternating stacks of Se and [BiO] has hindered this process. In this work, we report the method for synthesizing a BiOSe film on amorphous alumina (AlO) directly at 350 °C by using chemical solution deposition.
View Article and Find Full Text PDFA simple cavity-enhanced laser-based heater for reflective samples.
Rev Sci Instrum
January 2025
Institute for Physical Chemistry, University of Göttingen, 37077 Göttingen, Germany.
Surface science instruments require excellent vacuum to ensure surface cleanliness; they also require control of sample temperature, both to clean the surface of contaminants and to control reaction rates at the surface, for example, for molecular beam epitaxy and studies of heterogeneous catalysis. Standard approaches to sample heating within high vacuum chambers involve passing current through filaments of refractory metals, which then heat the sample by convective, radiative, or electron bombardment induced heat transfer. Such hot filament methods lead to outgassing of molecules from neighboring materials that are inadvertently heated; they also produce electrons and ions that may interfere with other aspects of the surface science experiment.
View Article and Find Full Text PDFHemoadhican Fiber Composite with Carbon Dots for Treating Severe Hemorrhage and Infected Wounds.
ACS Appl Mater Interfaces
January 2025
Center for Molecular Metabolism, Nanjing University of Science & Technology, Nanjing, Jiangsu 210094, China.
Uncontrolled bleeding and infection following trauma continue to pose significant clinical challenges. This study employs hemoadhican (HD) polysaccharide, known for its superior hemostatic properties, as the foundational material to synthesize antibacterial carbon dots (H-CDs) through a hydrothermal method at various temperatures. The H-CDs exhibiting optimal antimicrobial properties were identified via in vitro antimicrobial characterization.
View Article and Find Full Text PDFProspects of cold plasma in enhancing food phenolics: analyzing nutritional potential and process optimization through RSM and AI techniques.
Front Nutr
January 2025
Department of BioSciences, School of Bio Science and Technology (SBST), Vellore Institute of Technology, Vellore, India.
Consumption of plant-based food is steadily increasing and follows an augmented trend owing to their nutritive, functional, and energy potential. Different bioactive fractions, such as phenols, flavanols, and so on, contribute highly to the nutritive profile of food and are known to have a sensitivity toward higher temperatures. This limits the applicability of traditional thermal treatments for plant products, paving the way for the advancement of innovative and non-thermal techniques such as pulsed electric field, microwave, ultrasound, cold plasma, and high-pressure processing.
View Article and Find Full Text PDF3D-Printed PCL/SrHA@DFO Bone Tissue Engineering Scaffold with Bone Regeneration and Vascularization Function.
ACS Appl Bio Mater
January 2025
School of Materials Science and Physics, School of Chemical Engineering and Technology, China University of Mining and Technology, Xuzhou 221116, Jiangsu, China.
The application of a three-dimensional (3D)-printed biological functional scaffold in the repair of bone defects is a promising strategy. In this study, strontium-containing hydroxyapatite (SrHA) powder was synthesized by the hydrothermal method, and then poly(ε-caprolactone) (PCL)/HA and PCL/SrHA composite scaffolds were prepared by the high-temperature melt extrusion 3D printing technology. The basic physical and chemical properties, in vitro biological properties, osteogenesis, and angiogenesis abilities of the scaffold were studied.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!