The aim of this study was to evaluate intramural temperature-controlled radiofrequency ablation by determining the intramural temperature profile during ablation and by correlating lesion geometry with intramural electrode size and temperature. Intramural ablation might be useful to create deeper lesions for ventricular tachycardia secondary to underlying heart disease. Intramural radiofrequency ablation was performed in 17 greyhounds at thoracotomy, from an epicardial approach, using a 21-gauge needle electrode. Sixty-eight lesions were created in 11 dogs at electrode temperatures of 70 degrees C, 80 degrees C, 90 degrees C, and 100 degrees C for 60 seconds. Intramural thermocouples at 1-, 2-, 3-, 4-, and 5-mm distances were used to identify simultaneous intramural temperature profile. An epicardial approach was used to ensure accurate positioning of the ablating and temperature monitoring needles within the myocardium with fixed interneedle distances. Ninety-nine radiofrequency ablations were performed in six greyhounds using three different intramural electrode lengths (1 mm, 2.5 mm, and 5.5 mm). Lesions were created at 70 degrees C, 80 degrees C, and 90 degrees C for 60 seconds. All lesions were measured after staining with Gomori Trichrome. Lesion dimensions increased in a highly predictable manner with increasing electrode temperature or length. There was no popping or charring, even with target electrode temperature of 100 degrees C. There was significant correlation between intramural temperature 4 mm from the ablating electrode and lesion width (P < 0.001, R2= 0.45) and depth (P = 0.02, R2= 0.08). Feedback control of electrode temperature enables reliable intramural radiofrequency ablation without impedance rise even with target electrode temperature of 100 degrees C. Increasing the length of the intramural ablating electrode to > or = 5.5 mm and increasing temperatures to 90 degrees C-100 degrees C creates the largest lesions.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1111/j.1540-8159.2004.00519.x | DOI Listing |
ACS Appl Mater Interfaces
January 2025
State Key Laboratory for Manufacturing System Engineering, School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049, China.
Lithium dendrites are widely acknowledged as the main culprit of the degradation of performance in various Li-based batteries. Studying the mechanism of lithium dendrite formation is challenging because of the high reactivity of lithium metal. In this work, a phase field model and in situ observation experiments were used to study the growth kinetics and morphologies of lithium dendrites in terms of anisotropy, temperature, and potential difference.
View Article and Find Full Text PDFNat Nanotechnol
January 2025
Department of Chemical and Biomolecular Engineering, University of Maryland, College Park, MD, USA.
Room-temperature non-aqueous sodium metal batteries are viable candidates for cost-effective and safe electrochemical energy storage. However, they show low specific energy and poor cycle life as the use of conventional organic-based non-aqueous electrolyte solutions enables the formation of interphases that cannot prevent degradations at the positive and negative electrodes. Here, to promote the formation of inorganic NaF-rich interphases on both negative and positive electrodes, we propose the salt-in-presalt (SIPS) electrolyte formulation strategy.
View Article and Find Full Text PDFSmall
January 2025
College of Materials Science and Engineering, Sichuan University, Chengdu, 610065, China.
The transition metal single atoms (SAs)-based catalysts with M-N coordination environment have shown excellent performance in electrocatalytic reduction of CO, and they have received extensive attention in recent years. However, the presence of SAs makes it very difficult to efficiently improve the coordination environment. In this paper, a method of direct high-temperature pyrolysis carbonization of ZIF-8 adsorbed with Ni and Fe ions is reported for the synthesis of Ni SAs and FeN nanoparticles (NPs) supported by the N-doped carbon (NC) hollow nanododecahedras (HNDs) with nanotubes (NTs) on the surface (Ni SAs/FeN NPs@NC-HNDs-NTs).
View Article and Find Full Text PDFACS Appl Mater Interfaces
January 2025
Department of Chemistry and Biochemistry, University of California Santa Barbara, Santa Barbara, California 93106, United States.
Electrochemical aptamer-based (EAB) sensors are a molecular measurement platform that enables the continuous, real-time measurement of a wide range of drugs and biomarkers in situ in the living body. EAB sensors are fabricated by depositing a thiol-modified, target-binding aptamer on the surface of a gold electrode, followed by backfilling with an alkanethiol to form a self-assembled monolayer. And while the majority of previously described EAB sensors have employed hydroxyl-terminated monolayers, a handful of studies have shown that altering the monolayer headgroup can strongly affect sensor performance.
View Article and Find Full Text PDFRev Sci Instrum
January 2025
College of Electrical Engineering and Control Science, Nanjing Tech University, Nanjing 211816, Jiangsu, China.
Nanosecond pulse power has many driving advantages in the dielectric barrier discharge (DBD) application field, including better discharge effect, higher discharge efficiency, and lower electrode temperature. A high-voltage pulse voltage power supply (HV-PVPS) with a multi-turn ratio linear pulse transformer (PT) based on Marx circuit and PT topologies are suitable for most DBD plasma applications with fewer expansion modules, lower cost, smaller volume, and higher reliability comparing with the all-solid-state Marx nanosecond pulse power supply. However, during the process of DBD driven by an HV-PVPS based on Marx and PT topologies, the PT is prone to magnetic core saturation, which limits the application for DBD.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!