A fibre reinforced glass ionomer cement (FRGIC) for dental applications was loaded with 20 vol% short fibres (430 microm) with a glass composition in the system SiO(2)-Al(2)O(3)-CaF(2)-Na(3)AlF(6). The fracture toughness and the total energy release rate were examined. A 20% anisotropic fibre alignment was observed, perpendicular to the loading direction. An increase of fracture toughness of 140% and of total energy release rate of 440% was achieved compared to the unreinforced glass ionomer cement. Matrix-fibre interface reaction is supposed to exert the major influence on mechanical behaviour of FRGIC by controlling fibre pull-out and thus the total energy release rate.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.biomaterials.2003.12.027 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Measurement of Fluoride Ion Release From Restorative Material Using an Ion-Selective Electrode and Ultraviolet-Visible Light Spectrophotometer.
J Int Soc Prev Community Dent
December 2024
Department of Environmental Science, School of Life Sciences, Mysuru, JSS Academy of Higher Education and Research, Mysore, Karnataka, India.
Background: Importance of fluoride in dental restorative materials for preventing secondary caries. Several commercially available tooth-colored dental restorative materials, such as glass ionomer cement, resin composites, and compomers were used for this study.
Aim: To evaluate the amount of fluoride release from tooth-colored restorative materials [Conventional Glass Ionomer Cement (GC Fuji II)], Resin-modified Glass Ionomer Cement (ACTIVA BioACTIVE-RESTORATIVE), and Giomer (BEAUTIFIL II LS)] using ion-selective electrode (ISE) and spectrophotometer using zirconyl alizarin red dye method.
The Effect of Plaque Detectors on the Color Stability of Two Types of Restorative Materials.
J Esthet Restor Dent
January 2025
Department of Biomedical and Neuromotor Science (DIBINEM), Alma Mater Studiorum, University of Bologna, Bologna, Italy.
Objective: To investigate the color stability of a one-shade resin-based composite material (RC) and a glass-ionomer cement (GIC) after staining with plaque detectors (PDs) with different formulations and delivery forms.
Materials And Methods: Rectangular-shaped specimens (7 × 3 × 2 mm) were produced with RC (Venus Diamond One, Kulzer) and GIC (Fujy IX GP, GC) (n = 30). Further, the following PDs were used on the specimens: (1) tablets (T; Plaq-Search, TePe); (2) mouthwash (M; Plaque Agent, Miradent); and (3) light-curing liquid (L; Plaque test, Ivoclar).
Evaluation of Biodentine® and Calcium Hydroxide in the Formation of Dentin Bridge in Deep Carious Lesions.
West Afr J Med
September 2024
.Department of Preventive Dentistry, Lagos State University, College of Medicine, Faculty of Dentistry, Ikeja, Lagos, PMB 21266, Nigeria.
Background: Indirect pulp capping is the main treatment modality for reversible pulpitis.
Objective: To evaluate the efficacy of Biodentine® and Calcium hydroxide in the formation of dentin bridge.
Materials And Methods: A double blinded, randomized clinical control trial involving 50 consenting subjects, aged 16 to 55 years with deep carious vital teeth.
Effect of antacid gastric syrups on surface properties of dental restorative materials: an in vitro analysis of roughness and microhardness.
BMC Oral Health
January 2025
Faculty of Dentistry, Department of Restorative Dentistry, Inonu University, Malatya, Turkey.
Objectives: The aim of this in-vitro study was to evaluate the effects of antacid gastric syrups on the surface roughness and microhardness of restorative dental materials.
Materials And Methods: Three different composite resins, nanohybrid, microhybrid and giomer, and four antacid gastric syrups were used in the study. A total of 150 samples were obtained by preparing 50 (10 mm x 2 mm) disk-shaped samples of each composite type.
Purpose: To make micro-CT comparison and evaluation of sealant penetration depth in different types of fissures after heating of the material or application of vibrations.
Materials And Methods: One hundred sound third molars have been sealed as follows: group 1 (n = 20), light-cured resin sealant at room temperature, group 2 (n = 20), light-cured resin sealant, preheated to 41.0°C, group 3 (n = 20), light-cured resin sealant, preheated to 51.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!