Dental wastes are regulated under medical waste control regulations in most countries. Even though the quantity of hazardous wastes in dental solid wastes is a small proportion, there is still cross infection risk and potential danger for environment associated with mismanaged wastes. For this reason, knowledge of waste composition and development of proper management alternatives are necessary. In this study, the composition of solid wastes coming from eight clinics of the dental school of a University hospital in Turkey is examined. Although the waste has some variations between the two samplings, the general picture is such that the major components remain pretty much the same (in terms of %) for a fixed clinic. The composition of waste changes from one clinic to the other as expected. However, one can deduce from the data obtained that at about 35%, rubber gloves constitute close to the half of the total solid waste in almost all the clinics. Other major component is paper forming approximately 30% of the solid waste. In general, total waste coming from the clinics is related with the number of procedures conducted on patients at the clinics. Only a small fraction of the waste is hazardous indicating that at Hacettepe University School of Dentistry, hazardous waste collection rules are obeyed in most of the times.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.wasman.2003.08.002 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Framework for Site Specific Leachate Limits in MSW dumpsites: Integration of High-Resolution Site Characterization and Contaminant Transport Modeling.
Chemosphere
January 2025
Department of Civil Engineering, Indian Institute of Technology Delhi, New Delhi, Delhi, India, 110016. Electronic address:
The establishment of site-specific target limits (SSTLs) for old municipal solid waste (MSW) dumpsites is essential for defining remediation goals in a scientifically rigorous manner. However, a standardized framework for achieving this is currently lacking. This study proposes a comprehensive framework that integrates high-resolution site characterization (HRSC) tools, targeted sampling, and contaminant transport modeling to derive SSTLs.
View Article and Find Full Text PDFEnhanced copper extraction from waste printed circuit boards using glycine after supercritical methanol pre-treatment: Process optimization, leaching kinetics, and thermodynamic analysis.
Waste Manag
January 2025
Department of Environmental Science & Engineering, Indian Institute of Technology (Indian School of Mines), Dhanbad 826004, India. Electronic address:
The disposal of waste-printed circuit boards (WPCBs) poses significant environmental and health risks, as they are a major component of e-waste containing hazardous materials. However, WPCBs also contain valuable metallic elements, making them important resources for recycling. To address the dual challenge of hazardous waste management and resource recovery, sustainable approaches for metal extraction from WPCBs are imperative.
View Article and Find Full Text PDFProperties characterization and microstructural analysis of alkali-activated solid waste-based materials with sawdust and wastewater integration.
PLoS One
January 2025
Hebei Yingsheng New Material Technology Co., Ltd., Shijiazhuang, China.
Construction materials are significantly exposed to ecological hazards due to the presence of hazardous chemical constituents found in industrial and agricultural solid wastes. This study aims to investigate the use of sawdust particles (SDPs) and sawdust wastewater (SDW) in alkali-activated composites (AACs) made from a mixture of different silicon-aluminum-based solid wastes (slag powder-SP, red mud-RM, fly ash-FA, and carbide slag-CS). The study examines the impact of SDP content, treated duration of SDPs, and SDW content on both fresh and hardened properties of the AACs, including electrical conductivity, fluidity, density, flexural and compressive strengths, and drying shrinkage.
View Article and Find Full Text PDFAdsorption properties and mechanisms of Cd by co-pyrolysis composite material derived from peanut biochar and tailing waste.
Environ Geochem Health
January 2025
College of Resource and Environmental Engineering, Hubei Key Laboratory for Efficient Utilization and Agglomeration of Metallurgic Mineral Resource, Wuhan University of Science and Technology, Wuhan, 430081, People's Republic of China.
Cadmium (Cd) contamination in aquatic systems is a widespread environmental issue. In this study, a solid waste iron tailings and biochar hybrid (Fe-TWBC) was successfully synthesized derived from co-pyrolysis of peanut shell and tailing waste (Fe-TW). Characterization analyses showed that the metal oxides from solid waste iron tailings successfully loaded onto the biochar surface, with more functional groups in Fe-TWBC.
View Article and Find Full Text PDFNickel-Doping Induced Oxygen Vacancies in MnO Hollow Cube with Enlarged Interlayer Spacing for Stable Sodium Ions Storage.
Small
January 2025
School of Chemistry, South China Normal University, Guangzhou, 510006, P. R. China.
Intrinsic low conductivity, poor structural stability, and narrow interlayer spacing limit the development of MnO in sodium-ion (Na) supercapacitors. This work constructs the hollow cubic Mn-PBA precursor through an ion-exchange process to in situ obtain a hollow cubic H-Ni-MnO composite with Ni doping and oxygen vacancies (O) via a self-oxidation strategy. Experiments and theoretical calculations show that the hollow nanostructure and the expanding interlayer spacing induced by Ni doping are beneficial for exposing more reactive sites, synergistically manipulating the Na transport pathways.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!