Organic films were collected from indoor and outdoor window surfaces, along an urban-rural transect extending northward from Toronto, Ontario, Canada, and analyzed for 41 polybrominated diphenyl ether congeners (PBDE). For exterior films, urban sigmaPBDE concentrations were approximately 10x greater than rural concentrations, indicating an urban-rural gradient and greater PBDE sources in urban areas. Urban films ranged from 2.5 to 14.5 ng/m2 (mean = 9.0 ng/ m2), excluding the regional "hotspot" Electronics Recycling Facility, compared to 1.1 and 0.56 ng/m2 at the Suburban and Rural sites. Interior urban films (mean = 34.4 ng/m2) were 3 times greater than rural films (10.3 ng/m2) and were representative of variations in building characteristics. Indoor films were 1.5-20 times greater than outdoor films, consistent with indoor sources of PBDEs and enhanced degradation in outdoor films. Congener profiles were dominated by BDE-209 (51.1%), consistent with deca-BDE as the main source mixture, followed by congeners from the penta-BDE mixture (BDE-99:13.6% and -47:9.4%) and some octa-BDE (BDE-183:1.5%). Congener patterns suggest a degradative loss of lower brominated compounds in outdoor films versus indoor films. Gas-phase air concentrations were back-calculated from film concentrations using the film-air partition coefficient (K(FA)). Mean calculated air concentrations were 4.8 pg/m3 for outdoor and 42.1 pg/m3 for indoor urban sites, indicating that urban indoor air is a source of PBDEs to urban outdoor air and the outdoor regional environment.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1021/es034670r | DOI Listing |
Nat Commun
January 2025
KAUST Solar Center (KSC), Physical and Engineering Division (PSE), King Abdullah University of Science and Technology (KAUST), Thuwal, Kingdom of Saudi Arabia.
The controlled growth of two-dimensional (2D) perovskite atop three-dimensional (3D) perovskite films reduces interfacial recombination and impedes ion migration, thus improving the performance and stability of perovskite solar cells (PSCs). Unfortunately, the random orientation of the spontaneously formed 2D phase atop the pre-deposited 3D perovskite film can deteriorate charge extraction owing to energetic disorder, limiting the maximum attainable efficiency and long-term stability of the PSCs. Here, we introduce a meta-amidinopyridine ligand and the solvent post-dripping step to generate a highly ordered 2D perovskite phase on the surface of a 3D perovskite film.
View Article and Find Full Text PDFInt J Biol Macromol
January 2025
School of Chemistry and Materials Science, Hubei Engineering University, Xiaogan 43200, China.
Passive Radiant Cooling and Heating are green and sustainable methods of radiant heat management without consuming additional energy. However, the absorption of sunlight and poor insulation of materials can reduce radiative cooling and also affect radiative heating performance. Herein, we have constructed porous hierarchical dual-mode silk nanofibrous aerogel (SNF) films with high mechanical toughness and stability using silk nanofibers/GO.
View Article and Find Full Text PDFMaterials (Basel)
January 2025
College of Civil Engineering, Nanjing Forestry University, Nanjing 210037, China.
The global asphalt production growth rate exceeded 10% in the past decade, and over 90% of the world's road surfaces are generated from asphalt materials. Therefore, the issue of asphalt aging has been widely researched. In this study, the aging of asphalt thin films under various natural conditions was studied to prevent the distortion of indoor simulated aging and to prevent the extraction of asphalt samples from road surfaces from impacting the aged asphalt.
View Article and Find Full Text PDFSmall
January 2025
School of Mechanical Engineering, Korea University, 145 Anam-Ro, Seongbuk-Gu, Seoul, 02841, Republic of Korea.
Passive temperature controls like passive daytime radiative cooling (PDRC)-heating (PDRH), and thermal insulation are essential to meet the growing demand for energy-efficient thermal solutions. When combined with advanced functions like electromagnetic interference shielding, these technologies can significantly enhance scalability. However, existing approaches using single thin films or uniform porous materials face inherent limitations in optimizing versatile functions, while lightweight, insulating aerogels can extend their multifunctionality by manipulating pores and fillers.
View Article and Find Full Text PDFSmall
December 2024
School of Energy Science and Engineering, University of Science and Technology of China, Hefei, 230026, P. R. China.
Flexible perovskite solar cells (FPSCs) have great promise for applications in wearable technology and space photovoltaics. However, the unpredictable crystallization of perovskite on flexible substrates results in significantly lower efficiency and mechanical durability than industry standards. A strategy is investigated employing the polymer electrolyte poly(allylamine hydrochloride) (PAH) to regulate crystallization and passivate defect states in perovskite films on flexible substrates.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!