In multiple-pass nonlinear frequency conversion devices, interacting waves may accumulate different phases, owing to dispersive elements in the system. Phase compensation is therefore necessary for efficient frequency conversion. We experimentally demonstrate phase compensation in a compact semimonolithic frequency-doubling cavity by using a periodically poled KTP crystal. The conversion efficiency of the crystal was found to decrease at high pump powers, owing to power-dependent thermal lensing. This experimental observation was supported by a theoretical calculation of the conversion efficiency in a cavity, considering the mismatch between the mode's thermally loaded and unloaded cavities. A design procedure was also presented to compensate for the thermal lensing effect. The highest conversion efficiency of 56.5%, corresponding to a second-harmonic power of 117.5 mW at 532 nm, was achieved with a cw Nd:YAG pump power of 208 mW.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/ao.42.007163 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Pulsed-Current Operation Enhances HO Production on a Boron-Doped Diamond Mesh Anode in a Zero-Gap PEM Electrolyzer.
ChemSusChem
January 2025
Department of Chemical Engineering, MESA+ Institute for Nanotechnology, Faculty of Science and Technology, University of Twente, Drienerlolaan 5, 7522 NB, Enschede, The, Netherlands.
A niobium (Nb) mesh electrode was coated with boron-doped diamond (BDD) using chemical vapor deposition in a custom-built hot-filament reactor. The BDD-functionalized mesh was tested in a zero-gap electrolysis configuration and evaluated for the anodic formation of HO by selective oxidation of water, including the analysis of the effects on Faradaic efficiency towards HO (FEH2O2) induced by pulsed electrolysis. A low electrolyte flow rate (V⋅) was found to result in a relatively high concentration of HO in single-pass electrolysis experiments.
View Article and Find Full Text PDFSolvent Selection as a Key Factor in the Performance of Semitransparent Heterojunctions Composed of Hydrogenated Nanotubes and Bismuth Sulfides.
ACS Appl Mater Interfaces
January 2025
Centre for Plasma and Laser Engineering, Institute of Fluid-Flow Machinery, Polish Academy of Sciences, 14 Fiszera Street, 80-231 Gdańsk, Poland.
Research on titanium nanotubes modified with metal sulfides, particularly bismuth sulfide (BiS), aims to create heterostructures that efficiently absorb sunlight and then separate photogenerated charge carriers, thereby enhancing the energy conversion efficiency. This study shows a key role of solvent used for sulfide and bismuth salt solutions used during successive ionic layer adsorption and reaction (SILAR) onto the morphology, structure, and photoresponse of the heterojunction where one element is represented by semitransparent titania nanotubes (gTiNT) and the second is BiS. Using 2-methoxyethanol and methanol during SILAR, results in remarkably photoactive 3D heterostructure and recorded photocurrents were 44 times higher compared to bare titania nanotubes.
View Article and Find Full Text PDFCustomized Design of Covalent Organic Framework with Asymmetric Dual-Function Hybrid Linkages for Promoting HO Photosynthesis in Air and Water.
Nano Lett
January 2025
National Key Laboratory of Uranium Resources Exploration-Mining and Nuclear Remote Sensing, East China University of Technology, Nanchang 330013, China.
Efficient sacrificial-agent-free photosynthesis of HO from air and water represents the greenest, lowest-cost, most real-time avenue for HO production but remains a challenging issue. Here, we show a general and effective approach through a structural design on covalent organic frameworks (COFs) with asymmetric dual-function hybrid linkages for boosting the HO photosynthesis of the COFs. Through such design we can equip a COF with not only a catalytic active center but also a special function for isolating the D-A motif, which consequently endows the COF (CI-COF) built on asymmetric dual-function hybrid linkages with a significantly enhanced efficiency in the generation, transmission, and separation of photogenerated carriers, relative to the COF (II-COF and CC-COF) built on symmetric single-function single linkages.
View Article and Find Full Text PDFThe Effect of Antisolvent Treatment on the Growth of 2D/3D Tin Perovskite Films for Solar Cells.
ACS Energy Lett
January 2025
Department of Chemistry and Centre for Processable Electronics, Molecular Sciences Research Hub, Imperial College London, London W12 0BZ, U.K.
Antisolvent treatment is used in the fabrication of perovskite films to control grain growth during spin coating. We study widely incorporated aromatic hydrocarbons and aprotic ethers, discussing the origin of their performance differences in 2D/3D Sn perovskite (PEAFASnI) solar cells. Among the antisolvents that we screen, diisopropyl ether yields the highest power conversion efficiency in solar cells.
View Article and Find Full Text PDFSulfur Vacancies Limit the Open-Circuit Voltage of SbS Solar Cells.
ACS Energy Lett
January 2025
Department of Materials, Imperial College London, Exhibition Road, London SW7 2AZ, U.K.
Antimony sulfide (SbS) is a promising candidate as an absorber layer for single-junction solar cells and the top subcell in tandem solar cells. However, the power conversion efficiency of SbS-based solar cells has remained stagnant over the past decade, largely due to trap-assisted nonradiative recombination. Here we assess the trap-limited conversion efficiency of SbS by investigating nonradiative carrier capture rates for intrinsic point defects using first-principles calculations and Sah-Shockley statistics.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!